B. S. Keerthi Gowda

B. S. Keerthi Gowda

Auto-generated profile, based on publicly available information

B. S. Keerthi Gowda

VTU PG Studies

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2017 in Procedia Engineering
Verified
Journal Article
Open access
GPG.L. Easwara Prasad
G.L. Easwara Prasad
BGB.S. Keerthi Gowda
B.S. Keerthi Gowda
RVR. Velmurugan
R. Velmurugan

1 January 2017 in Procedia Engineering
Verified
Journal Article
Open access
GPG.L. Easwara Prasad
G.L. Easwara Prasad
BGB.S. Keerthi Gowda
B.S. Keerthi Gowda
RVR. Velmurugan
R. Velmurugan

8 November 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
DND. C. Naveen
D. C. Naveen
NKNaresh Kakur
Naresh Kakur
BGB. S. Keerthi Gowda
B. S. Keerthi Gowda
MGMadhu Sudana Reddy G
Madhu Sudana Reddy G
Durga Prasad CDurga Prasad C
Durga Prasad C
RSRagavanantham Shanmugam
Ragavanantham Shanmugam
In recent times, thermoplastic waste materials are being extensively used as fine and coarse aggregates in the concrete mix as an environmentally friendly construction material. This study aims at utilizing polypropylene (PP) as a partial substitute for the conventional coarse aggregates in M30 grade concrete. The different replacement levels of coarse aggregates such as 0%, 20%, 40%, and 60% by weight were used in concrete. Sieve analysis, specific gravity, and water absorption tests were performed in all replacement levels of aggregates. The mechanical (compressive and split tensile tests) tests were conducted after 3, 14, and 28 days. The change in mechanical properties of concrete with the addition of different weight proportions of plastics was studied experimentally. Further, experimental values were predicted using the two-parameter Weibull distribution and artificial neural network (ANN)-based statistical approaches. The Levenberg–Marquardt algorithm was used in predicting the mechanical properties using the ANN. A good correlation was obtained between the experimental and predicted values with an error (%) of less than 10. The decrease in mechanical properties with the increase in replacement levels of coarse aggregates in concrete was observed in both experimental and predicted approaches. This can be attributed to poor bonding between concrete and PP aggregate owing to the development of agglomerations and the hydrophobic nature of PP. However, the strength values of 20% PP-embedded concrete specimens are closer to 0% PP-embedded concrete specimens. Therefore, 20% PP-embedded concrete specimens can be used for primary load-bearing applications to utilize plastic waste and reduce the cost of the component.

11 April 2021 in Journal of Natural Fibers
Verified
Journal Article
Closed access
BGB. S. Keerthi Gowda
B. S. Keerthi Gowda
KNK. Naresh
K. Naresh
ISIlangovan S
Ilangovan S
MSM.R. Sanjay
M.R. Sanjay
Suchart SiengchinSuchart Siengchin
Suchart Siengchin
In general, the wood materials are used for constructing the buildings, passenger seats in trains and automobile doors. However, the progression of the fires due to the wooden construction is high when the fire accidents have occurred in the buildings, rail and road vehicles. To overcome this, advanced basalt fiber reinforced polymer composites can be replaced with these wood materials, owing to the high melting point of basalt fiber. However, fire resistance characterization studies are limited to natural fiber composites of different fiber volume fractions, particularly for rock fibers. There is a need to identify the fiber volume fraction effect on fire resistance characteristics of composites for filling this research gap. In this study, mechanical, water absorption, and fire resistance properties of Basalt Rock Fibers (BRF) and Pineapple Leaf Fibers (PLF) reinforced polyester composite panels were investigated. The effect of fiber volume fractions ranging from 10% to 45% on the above-mentioned properties was studied. The theoretical Young’s modulus values were determined using the Halpin-Tsai model. Results indicated that the mechanical properties of BRF/polyester and PLF/polyester composites increased with the increase in fiber volume fraction (FVF) of up to 40% and 30%, respectively. The theoretical Young’s modulus values are in reasonably good agreement with the experiments. The percentage of the linear burning rate was found to be decreased, with the increase in FVF. It was found through the water absorption studies that PLF/polyester composites are hydrophilic whereas BRF/polyester composites are hydrophobic.

22 July 2013
Verified
Book Chapter
Closed access
PDF file
GPG. L. Easwara Prasad
G. L. Easwara Prasad
BGB. S. Keerthi Gowda
B. S. Keerthi Gowda
RVR. Velmurugan
R. Velmurugan

1 January 2017 in Materials Today: Proceedings
Verified
Journal Article
Closed access
AAA.P. Abhishek
A.P. Abhishek
BGB.S. Keerthi Gowda
B.S. Keerthi Gowda
GPG.L. Easwara Prasad
G.L. Easwara Prasad
RVR. Velmurugan
R. Velmurugan