1 October 2016 in Journal of Materials Processing Technology
Additive manufacturing (AM) is a manufacturing technique that typically builds parts layer by layer, for example, in the case of selective laser melted (SLM) material by fusing layers of metal powder. This allows the construction of complex geometry parts, which, in some cases cannot be made by traditional manufacturing routes. Complex parts can be difficult to inspect for material conformity and defects which are limiting widespread adoption especially in high performance arenas. Spatially resolved acoustic spectroscopy (SRAS) is a technique for material characterisation based on robustly measuring the surface acoustic wave velocity. Here the SRAS technique is applied to prepare additively manufactured material to measure the material properties and identify defects. Results are presented tracking the increase in the measured velocity with the build power of the selective laser melting machine. Surface and subsurface defect measurements (to a depth of ∼24 μm) are compared to electron microscopy and X-ray computed tomography. It has been found that pore size remains the same for 140 W to 190 W melting power (mean: 115–119 μm optical and 134–137 μm velocity) but the number of pores increase significantly (70–126 optical, 95–182 velocity) with lower melting power, reducing overall material density
14 March 2014 in Measurement Science and Technology
30 October 2006 in Optics Express
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
1 August 2012 in The Journal of the Acoustical Society of America
A previously described laser ultrasonic technique known as spatially resolved acoustic spectroscopy (SRAS) can be used to image surface microstructure, using the local surface acoustic wave (SAW) velocity as a contrast mechanism. It is shown here that measuring the SAW velocity in multiple directions can be used to determine the crystallographic orientation of grains. The orientations are determined by fitting experimentally measured velocities to theoretical velocities. Using this technique the orientations of 12 nickel and 3 aluminum single crystal samples have been measured, and these are compared with x-ray Laue backreflection (LBR) measurements with good agreement. The root mean square difference between SRAS and LBR measurements in terms of an R-value is less than 4.1°. The influence of systematic errors in the SAW velocity determination due to instrument miscalibration, which affects the accurate determination of the planes, is discussed. SRAS has great potential for complementary measurements or even for replacing established orientation determination and imaging techniques.
1 April 2011 in The Journal of the Acoustical Society of America
A dual frequency mixing technique has been developed for measuring velocity changes caused by material nonlinearity. The technique is based on the parametric interaction between two surface acoustic waves (SAWs): The low frequency pump SAW generated by a transducer and the high frequency probe SAW generated and detected using laser ultrasonics. The pump SAW stresses the material under the probe SAW. The stress (typically <5 MPa) is controlled by varying the timing between the pump and probe waves. The nonlinear interaction is measured as a phase modulation of the probe SAW and equated to a velocity change. The velocity–stress relationship is used as a measure of material nonlinearity. Experiments were conducted to observe the pump–probe interaction by changing the pump frequency and compare the nonlinear response of aluminum and fused silica. Experiments showed these two materials had opposite nonlinear responses, consistent with previously published data. The technique could be applied to life-time predictions of engineered components by measuring changes in nonlinear response caused by fatigue.
1 January 2017 in Additive Manufacturing
Unlike more established subtractive or constant volume manufacturing technologies, additive manufacturing methods suffer from a lack of in-situ monitoring methodologies which can provide information relating to process performance and the formation of defects. In-process evaluation for additive manufacturing is becoming increasingly important in order to assure the integrity of parts produced in this way. This paper addresses the generic performance of inspection methods suitable for additive manufacturing. Key process and measurement parameters are explored and the impacts these have upon production rates are defined. Essential working parameters are highlighted, within which the spatial opportunity and temporal penalty for measurement allow for comparison of the suitability of different nondestructive evaluation techniques. A new method of benchmarking in-situ inspection instruments and characterising their suitability for additive manufacturing processes is presented to act as a design tool to accommodate end user requirements. Two inspection examples are presented: spatially resolved acoustic spectroscopy and optical coherence tomography for scanning selective laser melting and selective laser sintering parts, respectively. Observations made from the analyses presented show that the spatial capability arising from scanning parameters affects the temporal penalty and hence impact upon production rates. A case study, created from simulated data, has been used to outline the spatial performance of a generic nondestructive evaluation method and to show how a decrease in data capture resolution reduces the accuracy of measurement