Rikesh Patel

Dr. Rikesh Patel

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
ACAndrea Colombi
Andrea Colombi
VAVictoria Ageeva
Victoria Ageeva
RSRichard J. Smith
Richard J. Smith
ACAdam T. Clare
Adam T. Clare
RPRikesh Patel
Rikesh Patel
RCRichard V. Craster
Richard V. Craster
Recent years have heralded the introduction of metasurfaces that advantageously combine the vision of sub-wavelength wave manipulation, with the design, fabrication and size advantages associated with surface excitation. An important topic within metasurfaces is the tailored rainbow trapping and selective spatial frequency separation of electromagnetic and acoustic waves using graded metasurfaces. This frequency dependent trapping and spatial frequency segregation has implications for energy concentrators and associated energy harvesting, sensing and wave filtering techniques. Different demonstrations of acoustic and electromagnetic rainbow devices have been performed, however not for deep elastic substrates that support both shear and compressional waves, together with surface Rayleigh waves; these allow not only for Rayleigh wave rainbow effects to exist but also for mode conversion from surface into shear waves. Here we demonstrate experimentally not only elastic Rayleigh wave rainbow trapping, by taking advantage of a stop-band for surface waves, but also selective mode conversion of surface Rayleigh waves to shear waves. These experiments performed at ultrasonic frequencies, in the range of 400–600 kHz, are complemented by time domain numerical simulations. The metasurfaces we design are not limited to guided ultrasonic waves and are a general phenomenon in elastic waves that can be translated across scales.

1 October 2016 in Journal of Materials Processing Technology
Verified
Journal Article
Open access
RSRichard J. Smith
Richard J. Smith
MHMatthias Hirsch
Matthias Hirsch
RPRikesh Patel
Rikesh Patel
WLWenqi Li
Wenqi Li
ACAdam T. Clare
Adam T. Clare
SSSteve D. Sharples
Steve D. Sharples
Additive manufacturing (AM) is a manufacturing technique that typically builds parts layer by layer, for example, in the case of selective laser melted (SLM) material by fusing layers of metal powder. This allows the construction of complex geometry parts, which, in some cases cannot be made by traditional manufacturing routes. Complex parts can be difficult to inspect for material conformity and defects which are limiting widespread adoption especially in high performance arenas. Spatially resolved acoustic spectroscopy (SRAS) is a technique for material characterisation based on robustly measuring the surface acoustic wave velocity. Here the SRAS technique is applied to prepare additively manufactured material to measure the material properties and identify defects. Results are presented tracking the increase in the measured velocity with the build power of the selective laser melting machine. Surface and subsurface defect measurements (to a depth of ∼24 μm) are compared to electron microscopy and X-ray computed tomography. It has been found that pore size remains the same for 140 W to 190 W melting power (mean: 115–119 μm optical and 134–137 μm velocity) but the number of pores increase significantly (70–126 optical, 95–182 velocity) with lower melting power, reducing overall material density

19 October 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RPRikesh Patel
Rikesh Patel
MHMatthias Hirsch
Matthias Hirsch
PDPaul Dryburgh
Paul Dryburgh
DPDon Pieris
Don Pieris
SASamuel Achamfuo-Yeboah
Samuel Achamfuo-Yeboah
MCMatt Clark
Matt Clark
Additive manufacturing (AM) is a production technology where material is accumulated to create a structure, often through added shaped layers. The major advantage of additive manufacturing is in creating unique and complex parts for use in areas where conventional manufacturing reaches its limitations. However, the current class of AM systems produce parts that contain structural defects (e.g., cracks and pores) which is not compatible with certification in high value industries. The probable complexity of an AM design increases the difficulty of using many non-destructive evaluation (NDE) techniques to inspect AM parts—however, a unique opportunity exists to interrogate a part during production using a rapid surface based technique. Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasound inspection technique used to image material microstructure of metals and alloys. SRAS generates and detects `controlled’ surface acoustic waves (SAWs) using lasers, which makes it a non-contact and non-destructive technique. The technique is also sensitive to surface and subsurface voids. Work until now has been on imaging the texture information of selective laser melted (SLM) parts once prepared (i.e., polished with R a < 0.1 μ m)—the challenge for performing laser ultrasonics in-process is measuring waves on the rough surfaces present on as-deposited parts. This paper presents the results of a prototype SRAS system, developed using the rough surface ultrasound detector known as speckle knife edge detector (SKED)—texture images using this setup of an as-deposited Ti64 SLM sample, with a surface roughness of S a ≈ 6 μ m, were obtained.

1 January 2017 in Additive Manufacturing
Verified
Journal Article
Open access
MHMatthias Hirsch
Matthias Hirsch
RPRikesh Patel
Rikesh Patel
WLWenqi Li
Wenqi Li
GGGuangying Guan
Guangying Guan
Richard LeachRichard Leach
Richard Leach
ACAdam T. Clare
Adam T. Clare
Unlike more established subtractive or constant volume manufacturing technologies, additive manufacturing methods suffer from a lack of in-situ monitoring methodologies which can provide information relating to process performance and the formation of defects. In-process evaluation for additive manufacturing is becoming increasingly important in order to assure the integrity of parts produced in this way. This paper addresses the generic performance of inspection methods suitable for additive manufacturing. Key process and measurement parameters are explored and the impacts these have upon production rates are defined. Essential working parameters are highlighted, within which the spatial opportunity and temporal penalty for measurement allow for comparison of the suitability of different nondestructive evaluation techniques. A new method of benchmarking in-situ inspection instruments and characterising their suitability for additive manufacturing processes is presented to act as a design tool to accommodate end user requirements. Two inspection examples are presented: spatially resolved acoustic spectroscopy and optical coherence tomography for scanning selective laser melting and selective laser sintering parts, respectively. Observations made from the analyses presented show that the spatial capability arising from scanning parameters affects the temporal penalty and hence impact upon production rates. A case study, created from simulated data, has been used to outline the spatial performance of a generic nondestructive evaluation method and to show how a decrease in data capture resolution reduces the accuracy of measurement

1 March 2019 in Insight - Non-Destructive Testing and Condition Monitoring
Verified
Journal Article
Open access
DPD Pieris
D Pieris
RPRikesh Patel
Rikesh Patel
PDPaul Dryburgh
Paul Dryburgh
MHM Hirsch
M Hirsch
WLW Li
W Li
MCM Clark
M Clark
High-integrity engineering applications such as aerospace will not permit the incorporation of components containing any structural defects. The current generation of additive manufacturing (AM) platforms yield components with relatively high levels of defects. The in-line inspection of components built using AM can provide closed-loop feedback and vary build parameters during fabrication to minimise defects. This article reviews the capability of spatially resolved acoustic spectroscopy (SRAS) to be used as an inspection tool for detecting defects and characterising microstructure in parts induced by variations in build parameters. The authors first correlated changes to surface acoustic wave velocity and an increase in defects to variations in build laser power, then identified changes to the component microstructure caused by variations in build laser scan strategy. This was carried out using the detected probe light intensity and the measured surface acoustic velocity.

1 November 2017 in Scripta Materialia
Verified
Journal Article
Open access
RPRikesh Patel
Rikesh Patel
WLWenqi Li
Wenqi Li
RSRichard J. Smith
Richard J. Smith
SSSteve D. Sharples
Steve D. Sharples
MCMatt Clark
Matt Clark
Due to its economical production process polysilicon, or multicrystalline silicon, is widely used to produce solar cell wafers. However, the conversion efficiencies are often lower than equivalent monocrystalline or thin film cells, with the structure and orientation of the silicon grains strongly linked to the efficiency. We present a non-destructive laser ultrasonic inspection technique, capable of characterising large (52 x 76 mm2) photocell's microstructure – measurement times, sample surface preparation and system upgrades for silicon scanning are discussed. This system, known as spatially resolved acoustic spectroscopy (SRAS) could be used to optimise the polysilicon wafer production process and potentially improve efficiency