Reducing the mode size mismatch between high-index-contrast silicon waveguide and single mode fiber takes an important role in photonic integration. A low-loss and broadband silicon nitride assisted edge coupler for coupling of light between silicon wire waveguides and high numerical aperture fiber is proposed and optimized for TE polarization. The mode size converter is composed of silicon inverse taper waveguides in core and two silicon nitride interlayers spaced by silica in cladding layers. The edge coupler is characterized with cleaved high numerical aperture fiber (mode field diameter is about 6.5 μm). With the help of refractive index matching oil (n = 1.46), the coupling loss for TE polarized light input is 0.35 dB at 1570 nm. The 1-dB bandwidth is 95 nm. The 1-dB alignment tolerances are higher than ± 2.5 μm and ± 1 μm in the horizontal and vertical directions, respectively, and higher than 25 μm in axial direction.
Based on the Si-Si3N4 hybrid photonic platform, an integrated edge coupler embedded with both sub-wavelength grating (SWG) waveguide and suspended structure was demonstrated. The proposed device structure and geometrical parameters were fully optimized to realize efficient optical interconnections with standard single-mode fiber (SMF-28). The coupling loss of 0.86 dB/port for TE mode and 0.94 dB/port for TM mode was achieved with a remarkable polarization dependent loss (PDL) less than 0.1 dB at the input wavelength of 1600 nm. It revealed that the integrated edge coupler assisted by sub-wavelength grating can further reduce the PDL. Moreover, the device also exhibited the advantages of large alignment tolerance. The alignment tolerances for 1-dB excess loss are ±1.8 and ±2.5 μm in horizontal and vertical direction, respectively.
An ultra-small polarization beam splitter on silicon-on-insulator platform is proposed and demonstrated experimentally employing a sharp bent directional coupler. The coupling length of our device is only 0.764 μ m. High-efficient selective coupling can be achieved benefiting from the inner bend chosen as Through port and ultra-small bend (radii are about 3 μ m) used in Through and Cross waveguides. The measured excess loss is less than 1 dB and extinction ratio is 15–20 dB for TM polarization, meanwhile, the measured excess loss is less than 2 dB and extinction ratio is 15-16 dB for TE polarization in a wavelength range from 1540 nm to 1580 nm. The fabrication tolerance to variation of waveguide width is also demonstrated. When the waveguide widths of the Through and Cross waveguides vary from −24 nm to +12 nm, the measured excess losses remain lower than 2 dB and the extinction ratios are higher than 10 dB for both polarizations. The footprint of the fabricated device is just 1.5 μ m × 1.3 μ m.
1 November 2014 in Electrochemistry Communications
Efficient fiber-to-chip coupling is crucial for achieving high-performance silicon photonic chips. While lensed fiber to chip coupling has been extensively researched and proven excellent, it does have limitations such as strict alignment tolerance and high cost. Therefore, the recommended approach is the standard single-mode fiber (SMF)-to-chip coupling. One potential solution for SMF-to-chip coupling involves an edge coupler based on a graded-index (GRIN) lens; however, this method often requires a GRIN lens with numerous layers, making fabrication extremely challenging. In this study, we propose and experimentally validate an edge coupler based on a GRIN lens assisted by a complementary taper structure. This new type of composite structure demonstrates low coupling loss, broad bandwidth, and polarization insensitivity, enabling efficient SMF-to-chip coupling. Our design simplifies the fabrication process by significantly reducing the number of layers in the GRIN lens while achieving lower coupling losses compared to conventional GRIN lens-based edge couplers. Experimental results demonstrate that at 1550 nm, the measured TE and TM mode coupling losses are 1.21 dB and 1.78 dB respectively, while maintaining the 1 dB bandwidth exceeding 90 nm.
2 August 2021 in Journal of Materials Science: Materials in Electronics
The ridge waveguide integrated grating couplers (GCs) in lithium niobate on insulator (LiNbO3, LNOI) were designed, fabricated and characterized. Two ends of the tapered GCs were connected by the subwavelength gratings (SWG) waveguide of a sub-micrometric-diameter, the photonic-wire SWG structure was featured with the profile of side-walls corrugations, and the effect of geometrical dimensions on the output optical response was investigated. All the devices structure patterns for the integrated LNOI GCs could be simultaneously defined by one step of electron-beam lithography, and then easily fabricated by the optimized dry-etching processes, followed by samples surface cleaning. After the fabrication, a low coupling loss of − 5.1 dB/coupler at the telecommunication wavelength of 1561 nm was measured in the best thin-film LiNbO3 (TFLN) surface grating coupler for quasi-transverse-electric (quasi-TE) polarized signals, and a broad 3-dB optical bandwidth of wider than 95 nm was also obtained. The compact components exhibited magnificent performance, and might show the potential functionalities for the TFLN-based integrated optical waveguide devices.