International audienceThe present study assesses the ability of two low-cost adsorbents - timber sawdust (TS- OH) and its alkaline treated analog (TS-ONa) - to remove two basic dyes, namely, Methylene Blue and Methyl Green, from aqueous solutions. The presence of new functional groups on the surface of TS-ONa resulted in a dramatic increase of surface polarity and the density of sorption sites, thereby improving the sorption efficiency of the cationic dyes. The results obtained from the sorp- tion characteristics have revealed that the sorption process for TS-ONa was uniform and rapid. The adsorption of cationic dyes reached equilibrium within the first 10 min of contact time and the trea- ted material acts efficiently in a wide pH range of dye solutions. The extent of adsorption was mea- sured through equilibrium sorption isotherms and analyzed using the Langmuir model. The monolayer saturation capacities for Methylene Blue are 694.44 and 1928.31 mg/g and for Methyl Green are 892.86 and 1821.33 mg/g for TS-OH and TS-ONa, respectively. Therefore, the chem- ically treated sawdust proved two- to threefold higher adsorption capacities of these dyes than those of the untreated analog. The exothermic nature of adsorption is demonstrated by a decrease of adsorption capacity with increasing temperature, and the negative value of free energy change indi- cated the spontaneity of adsorption. Desorption experiments with 1 M aqueous NaCl put into evi- dence that cationic dyes were completely desorbed from the matrices and the reusability of the TS- ONa matrix after three repeated cycles led to just a slight attenuation in its performance. These results show that alkaline treatment of a low value by-product of the timber industry leads to a powerful and efficient low-cost adsorbent, which may be used for the treatment of colored waste- waters
18 January 2018 in International Journal of Environmental Science and Technology
A brown marine alga, Cystoseira stricta, has been studied for its biosorption capacities of the heavy metallic ion, the Pb(II), in aqueous solutions. The brown alga (C) has been used without previous treatment and with chemical treatment to acid (H2SO4 1M: CS) and to sodium hydroxide (NaOH 1M: CB). The results have shown the influence of the particle size of the biomaterial on the extraction-removal of Pb(II). The application of the Langmuir adsorption model revealed the maximum capacities of adsorption of each material (C, CS, CB). The one specific to C. stricta treated by a solution of sodium hydroxide 1M (CB) was the most important (65mgg−1). The established isotherms at different temperatures showed that this parameter affects the adsorption. The best results are obtained for a temperature of 25°C, in comparison with those recorded at 50°C. Finally, the results of this study showed that C. stricta can be a good potential biosorbent of heavy metals, in particular, when it is treated by a basic solution
The biosorption of cadmium and lead by Penicillium sp. isolated from an uncontaminated soil was studied at different initial metal ions concentrations. The maximum removal yields were obtained at 5 mg/L initial metal concentration. The highest removal yields were 35.67% and 81.99% for cadmium and lead respectively in the single system. In the binary system, the removal yield increased to 90.99% and 97.48% for both metal ions at the same initial concentration. This study has also confirmed that Penicillium sp was able to grow in the presence of both metal ions at different concentrations. In addition, this study showed that Penicillium sp was more tolerant to cadmium than lead. Fungi have also shown a tolerance to high concentrations of toxic heavy metals.This study can provide useful information on the bioremoval of heavy metals such as Cd(II) and Pb(II) from wastewaters.
The objective of this study was the synthesis of various activated carbons from grape marc issued from oenological by-product as a biosorbent. The biosolid was then applied to remove an industrial dye (red bemacid ETL) in aqueous solution. Activation of the synthesized charcoal was carried out using a solution of zinc chloride induced by two physical methods (microwaves and heating at 300°C). The obtained materials are characterized by FTIR and SEM methods. Results from batch adsorption tests have shown that pH solution, initial dye concentration and contact time affect the adsorption mechanism. Removal of the industrial dye revealed second order kinetics, exothermic adsorption and isothermal adsorption of BET type.