Leonardo Lorenzo Bravo Roger

Leonardo Lorenzo Bravo Roger

Auto-generated profile, based on publicly available information

Leonardo Lorenzo Bravo Roger

UNICAMP

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
Euclides ChumaEuclides Chuma
Euclides Chuma
Yuzo IanoYuzo Iano
Yuzo Iano
LRLeonardo Lorenzo Bravo Roger
Leonardo Lorenzo Bravo Roger
Gabriel Gomes de OliveiraGabriel Gomes de Oliveira
Gabriel Gomes de Oliveira
GVGabriel Caumo Vaz
Gabriel Caumo Vaz
Sensors for detecting wear particles in fluid lubricants have been widely studied owing to their ability to diagnose mechanical machine conditions and to help in preventing mechanical failures caused by wear particles or contamination particles. The proposed novelty sensor was fabricated using photolithography to make the complementary split ring resonator (CSSR) on PCB and it utilized neodymium magnets at the center of the CSRR structure to attract ferrous wear particles. The proposed sensor was tested, and we found that it is highly sensitive and could detect 50 ppm of ferrous wear particles larger than 10 μm dissolved in mineral white oil ISO VG 15. The sensor of this article has a low-cost and can be used in different situations to measure the ferrous wear particles while monitoring the real-time mechanical equipment wear, as it can be easily integrated into them. The sensor offers good accuracy, and is insensitive to fluid transparency and bubble formation, unlike other sensors for detection of wear particles. Therefore, the proposed novelty sensor of this work is in line with Industry 4.0, which requires many low-cost sensors for continuous monitoring to apply predictive maintenance techniques for extending the lifespan of infrastructures.

6 May 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
Euclides ChumaEuclides Chuma
Euclides Chuma
LRLeonardo Lorenzo Bravo Roger
Leonardo Lorenzo Bravo Roger
BMBezhko Mikhail
Bezhko Mikhail
This study presents a portable, compact, and cost-effective in situ monitoring device designed to monitor leaf water status through a terahertz (THz) source, THz sensor, and infrared array sensor. The innovation in the proposed device is the use of Resonant Tunnelling Diodes (RTD) within THz sources and detectors operating at ~0.28 THz and using a low-cost system’s architecture that consists of an integrated signal generator and scope, coupled with associated hardware connected to a computer. This configuration enables signal acquisition and subsequent Fast Fourier Transform (FFT) processing to extract peak power values to determine the plant leaf’s water content and the leaf surface’s temperature using an infrared array sensor. Experimental analysis demonstrates that the proposed THz system exhibits a substantial correlation, with an R-squared value of approximately 0.97, when compared to moisture loss measurements obtained using a moisture analyzer. Furthermore, it effectively detects moisture loss within the range of 25% to 85% and utilizes thermal images from an infrared sensor array to identify potential health issues in plants. Therefore, the device proposed in this work demonstrates a portable, in situ, non-destructive, and cost-effective solution tool for directly assessing water stress or drought conditions within a plant.

27 August 2014 in ECTI Transactions on Electrical Engineering, Electronics, and Communications
Verified
Journal Article
Open access
PDF file
FAFrancisco Arnold
Francisco Arnold
MGMarcos S. Gonçalves
Marcos S. Gonçalves
LRLeonardo L. Bravo Roger
Leonardo L. Bravo Roger
SMSérgio S. Mühlen
Sérgio S. Mühlen
The electric impedance of piezoelectric ceramics is influenced by variations in the acoustic load. This situation is very common for ultrasonic applications in medicine where the irradiated media can present different interfaces and impedances to the propagating acoustic energy. In this work we analyzed the behavior of the resonances, anti-resonances and the effective electromechanical coupling factor of a piezoelectric ceramic ring vibrating in thickness mode. The analysis is based on equivalent electric circuits and considers variations in the acoustic load. The results showed that the electric impedance of the ceramic is altered with the length of the acoustic load, resulting in new resonances and changing the effective electromechanical coupling factor. Electronic circuits for driving piezoelectric transducers must be able to correct the frequencies if acoustic loads vary.

1 June 2019 in Journal of Microwaves, Optoelectronics and Electromagnetic Applications
Verified
Journal Article
Open access
PDF file
Euclides ChumaEuclides Chuma
Euclides Chuma
Yuzo IanoYuzo Iano
Yuzo Iano
LRLeonardo L. Bravo Roger
Leonardo L. Bravo Roger
MSMathias Scroccaro
Mathias Scroccaro
FFFelipe Frazatto
Felipe Frazatto
LMLeandro Manera
Leandro Manera
In this study are analyzed horn antennas to operating at X band (8 – 12 GHz) and manufactured by additive manufacturing method (AM). To construct the antennas using AM method was necessary made the structure with acrylonitrile butadiene styrene (ABS) thermoplastic using a 3D printer, and then coated the antennas with conductive surfaces. Were fabricated three antennas with different coated techniques: the first antenna with conductive silver paint, the second antenna using copper tape and the third antenna using copper plated. It is investigated the performances of these antennas in terms of the input reflection coefficient, gain, radiation pattern, weight and compared with the conventional aluminum horn antenna with same dimensions.

1 December 2012 in Engenharia Agrícola
Verified
Journal Article
Open access
PDF file
CRClerivaldo Roccia
Clerivaldo Roccia
BTBarbara Teruel
Barbara Teruel
EAElaine C. de S. Alves
Elaine C. de S. Alves
FAFrancisco Arnold
Francisco Arnold
LBLeonardo Bravo-Roger
Leonardo Bravo-Roger
MGMarcos S. Gonçalves
Marcos S. Gonçalves

1 August 2017
Verified
Conference Paper
Closed access
Euclides ChumaEuclides Chuma
Euclides Chuma
YIYuzo Iano
Yuzo Iano
LRLeonardo L. Bravo Roger
Leonardo L. Bravo Roger
This work presents the design of a compact antenna using microstrip patch based on a fractal model for use in Internet-of-Things (IoT) wireless communication in sub-GHz bands. The proposed antenna was implemented on a low cost FR-4 substrate and work in the 433 MHz and 915 MHz or 868 MHz frequencies that are ISM bands used in the IoT networks. The suggested antenna has been manufactured and experimentally characterized, showing a good agreement with the expected simulated results.