Abir Alabani

Abir Alabani

Auto-generated profile, based on publicly available information

Abir Alabani

Department of Electrical and Electronic Engineering, The University of Manchester, Manchester, U.K.

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2023 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
AAAbir Alabani
Abir Alabani
PRPrem Ranjan
Prem Ranjan
JJJun Jiang
Jun Jiang
LCLujia Chen
Lujia Chen
ICIan Cotton
Ian Cotton
VPVidyadhar Peesapati
Vidyadhar Peesapati
Arcing in future high-voltage aerospace systems could occur more frequently and cause irreversible damage to electrical components, system structure and increase the risk of fire. While arcs seen in low-voltage aerospace systems tend to be long-duration and low-energy events, higher power but short-duration arcs may occur in high-voltage aerospace systems if they are readily detectable by system protection. This paper investigates the characteristics of high current arc faults generated at the AC frequencies expected in future rotating machines used for higher voltage aerospace systems. As such, arcs with a peak current up to 4.6 kA are generated at frequencies in the range of 0.5-2 kHz using an underdamped RLC circuit, under pressures of 0.2-1 bar absolute. High frequency arcs exhibit a similar characteristic to lower frequency arcs. A reduction in pressure results in lower arc voltage and arc power. Arcing tests at atmospheric pressure may therefore represent a worst-case scenario and the development of a low-pressure test environment may not be necessary. A black box model is developed to provide good agreement with experimental arc voltage waveforms for different parameters investigated in this study. This is a generalized modeling approach to estimate high-frequency high-voltage arcing characteristics without recourse to experiment.

15 October 2024 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
AAAbir Alabani
Abir Alabani
RSRaul Negrin Sanchez
Raul Negrin Sanchez
ICIan Cotton
Ian Cotton
LCLujia Chen
Lujia Chen
Higher on-board electrical power generation is a promising solution to significantly reduce greenhouse gas emissions generated by the aviation industry. With the increasing level of operating voltages to meet the electrical power generation requirements and the higher system frequencies to optimize weight, arc faults will become a serious threat to future aircraft electrical systems. Other conditions such as short electrode gap, low relative humidity and low-pressure ambient environment will introduce additional technical challenges. To provide better understanding of electric arcs at aeronautical conditions, this paper investigates high current (1–1.7 kA) arcs at high frequencies (150–1000 Hz) for a range of electrode gap lengths between 2.5 and 40 mm under pressures between 0.2 to 1 bar absolute. The arc conductance, used as a parameter for comparison of arc characteristics across arc models, is found to increase at shorter gaps, lower pressures, higher humidities and lower frequencies. A black box model is used to demonstrate comparable simulated and experimental arc waveforms below the atmospheric pressure. This modeling approach provides good estimation of high-frequency high-voltage arcing characteristics under aerospace conditions without the need to perform extensive experimental testing.

12 December 2021
Verified
Conference Paper
Closed access
AAA. Alabani
A. Alabani
PRPrem Ranjan
Prem Ranjan
JJJun Jiang
Jun Jiang
LCL. Chen
L. Chen
ICI. Cotton
I. Cotton
VPV. Peesapati
V. Peesapati
There is a drive in the aviation industry towards more-electric aircraft (MEA) to replace fuel-driven airplane engines with more-electric power systems and improved efficiency. This requires a higher on-board electric power generation and a higher operating frequency to maintain a compact power system architecture. However, higher operating voltages in aeronautical environment, coupled with the need to maintain compact design, increase the risk of arcing. Arc faults are characterized by their high current magnitude which could lead to a significant release of energy that may damage the equipment as well as the adjacent components. The length of the electrode gap across which the arc ignites is one factor that determines the arc severity. This paper investigates the arc over a range of electrode gaps from 2.5 to 100 mm under atmospheric pressure and within a high-frequency circuit. For gaps ≤ 40 mm, the arc voltage increases as the arc cools down, whilst for gaps ≥ 50 mm the arc voltage decreases. The results conclude that longer gaps in this underdamped circuit setup exhibit a lower arc voltage with lower arc current, which is different to the arc behavior observed in shorter electrode gaps.