Xiaojun Guo

Xiaojun Guo

Auto-generated profile, based on publicly available information

Xiaojun Guo

AECC Hunan Aviat Powerplant Res Inst, Zhuzhou 412002, Peoples R China

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
XLXiaochong Liu
Xiaochong Liu
XGXiaojun Guo
Xiaojun Guo
YXYouliang XU
Youliang XU
Longbiao LiLongbiao Li
Longbiao Li
WZWang Zhu
Wang Zhu
XHXiaoAn Hu
XiaoAn Hu
In this paper, the SiC/SiC high-pressure turbine twin guide vanes were fabricated using the chemical vapor infiltration (CVI) method. Cyclic thermal shock tests at different target temperatures (i.e., 1400, 1450, and 1480 °C) in a gas environment were conducted to investigate the damage mechanisms and failure modes. During the thermal shock test, large spalling areas appeared on the leading edge and back region. After 400 thermal shock cycles, the spalling area of the coating at the basin and back region of the guide vane was more than 30%, and the whole guide vane turned gray, due to the formation of SiO2. When the thermal shock temperature increased from 1400 to 1450 and 1480 °C, the spalling area of the basin and the back region of the guide vane did not increase significantly, but the delamination occurred at the tenon, upper surface of the guide vane near the trailing edge of the guide vane. Through the X-ray Computed Tomography (XCT) analysis for the guide vanes before and after thermal shock, there was no obvious damage inside of guide vanes. The oxidation of SiC coating and the formation of SiO2 protects the internal fibers from oxidation and damage. Further investigation on the effect of thermal shock on the mechanical properties of SiC/SiC composites should be conducted in the future.

21 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
XLXiao Luo
Xiao Luo
JHJiangyi He
Jiangyi He
XLXiaochong Liu
Xiaochong Liu
YXYouliang XU
Youliang XU
JLJian Li
Jian Li
Longbiao LiLongbiao Li
Longbiao Li
In this paper, the 12k T-700TM Multiaxial-Warp-Knitting–Needle (MWK–N) C/SiC composite and pin were designed and fabricated using the isothermal chemical vapor infiltration (ICVI) method. The composite’s microstructure and mechanical properties were examined by subjection to tensile and interlaminar shear tests. Three types of double-shear tests were conducted for C/SiC pins, including shear loading perpendicularly, along, and at 45° off-axial to the lamination. The fracture surface of the tensile and shear failure specimens was observed under scanning electronic microscope (SEM). The relationships between the composite’s microstructure, mechanical properties, and damage mechanisms were established. The composite’s average tensile strength was σuts = 68.3 MPa and the average interlaminar shear strength was τu = 38.7 MPa. For MWK–N–C/SiC pins, the double-shear strength was τu = 76.5 MPa, 99.7 MPa, and 79.6 MPa for test types I, II, and III, respectively. Compared with MWK–C/SiC pins, the double-shear strength of MWK–N–C/SiC pins all decreased, i.e., 26.7%, 50.8%, and 8% for test types I, II, and III, respectively. The MWK–N–C/SiC composite and pins possessed high interlaminar shear strength and double-shear strength, due to the needled fiber in the thickness direction, low porosity (10–15%), and high composite density (2.0 g/cm3).

17 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
RWRongqiao Wang
Rongqiao Wang
YLYu Liu
Yu Liu
LXLiu Xi
Liu Xi
DHDianyin Hu
Dianyin Hu
JHJiangbo Han
Jiangbo Han
XGXiaojun Guo
Xiaojun Guo
A geometric partitioning strategy was proposed to evaluate the mechanical properties of three-dimensional needled composites. The microstructure of the composite was divided to accurately characterize the mesoscopic damage in the needling regions and the macroscopic damage in the un-needling regions, to balance the computational accuracy and efficiency. The general method of cells (GMC) models along with the damage criteria were established for different material phases in the needling regions, while the continuum damage mechanics (CDM) model was adopted to portray the damage evolution in the un-needling regions. Through conducting the multi-scale simulation, the mechanical properties of the needled composites were predicted, based upon which the effect of repeated needling on the mesoscale damage process was further investigated. Results showed that the predictions are in good agreement with the experiments, with a relative error of 2.6% for strength and 4.4% for failure strain. The proposed approach can provide guidance for the process optimization and design of needled composites.

15 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
JMJianxing Mao
Jianxing Mao
XZxiao zhixing
xiao zhixing
DHDianyin Hu
Dianyin Hu
XGXiaojun Guo
Xiaojun Guo
RWRongqiao Wang
Rongqiao Wang
The creep-fatigue crack growth problem remains challenging since materials exhibit different linear and nonlinear behaviors depending on the environmental and loading conditions. In this paper, we systematically carried out a series of creep-fatigue crack growth experiments to evaluate the influence from temperature, stress ratio, and dwell time for the nickel-based superalloy GH4720Li. A transition from coupled fatigue-dominated fracture to creep-dominated fracture was observed with the increase of dwell time at 600 °C, while only the creep-dominated fracture existed at 700 °C, regardless of the dwell time. A concise binomial crack growth model was constructed on the basis of existing phenomenal models, where the linear terms are included to express the behavior under pure creep loading, and the nonlinear terms were introduced to represent the behavior near the fracture toughness and during the creep-fatigue interaction. Through the model implementation and validation of the proposed model, the correlation coefficient is higher than 0.9 on ten out of twelve sets of experimental data, revealing the accuracy of the proposed model. This work contributes to an enrichment of creep-fatigue crack growth data in the typical nickel-based superalloy at elevated temperatures and could be referable in the modeling for damage tolerance assessment of turbine disks.

1 October 2022 in Materials Research Express
Verified
Journal Article
Open access
HZHaiyan Zhu
Haiyan Zhu
XQXiangming Qu
Xiangming Qu
JCJun Cao
Jun Cao
XGXiaojun Guo
Xiaojun Guo
YZYanyun Zhao
Yanyun Zhao
YZYong-Kang Zhang
Yong-Kang Zhang
Aiming at the phenomenon that the residual stress induced by Laser Shock Peening (LSP) will relax and redistribute under various loads, temperature, cyclic load, and the dual treatment of temperature and cyclic load on the residual stress relaxation of FGH95 powder superalloy after LSP treatment were studied, and the analysis model of relevant residual stress relaxation was constructed. The purpose is to understand the strengthening effect and stability of the alloy under temperature and cyclic load after LSP treatment. With the increase of treatment temperature, the relaxation of residual stress became more and more obvious. Most of the residual stress relaxation occurred in the first 30 min of temperature treatment, then slowed down and stabilized after 1 h. The residual stress was initially relaxed in the first 50 cycles, remained roughly unchanged between 50 and 5000 cycles. The intensify of the cyclic load increasing, adding material yield level, further plastic deformation and residual stress relaxation rate increases. With the increase of load intensify and load ratio, residual stress relaxation was also increased. The residual stress relaxation rate after 600 °C and cyclic load treatment was 56.2%, both greater than that after 600 °C or cyclic treatment of 25 °C, but less than the sum of the two conditions. The results of this paper provide a reference for the LSP of the FGH95 powder superalloy turbine disk and other aero engine parts.

26 May 2015
Verified
Book Chapter
Closed access
PDF file
XHXuan Haijun
Xuan Haijun
LLLuo Ling
Luo Ling
GXGuo Xiaojun
Guo Xiaojun
LGLi Guoqiang
Li Guoqiang