Arne Røyset

Arne Røyset

Auto-generated profile, based on publicly available information

Arne Røyset

SINTEF Materials and Chemistry, NO-7465 Trondheim, Norway

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 1996 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
LBL. Bjerkan
L. Bjerkan
ARA. Royset
A. Royset
LHL. Hafskjaer
L. Hafskjaer
DMD. Myhre
D. Myhre
The semiconductor laser rate equations are rewritten using a new set of parameters which can all be found from steady state and small signal measurements on the laser. Procedures for finding these parameters are described. Parameters have been measured on three 1550 mm lasers from different manufacturers. Comparison between large signal measurements and simulations using the measured parameters shows in general good agreement for modulation currents sufficiently above threshold.

1 October 2013 in The Journal of Physical Chemistry C
Verified
Journal Article
Closed access
EFEspen Flage−Larsen
Espen Flage−Larsen
ARArne Røyset
Arne Røyset
JCJasmina Hafizovic Cavka
Jasmina Hafizovic Cavka
KTKnut Thorshaug
Knut Thorshaug

8 January 2008 in International Journal of Occupational Safety and Ergonomics
Verified
Journal Article
Closed access
RRRandi Eidsmo Reinertsen
Randi Eidsmo Reinertsen
HFHilde Færevik
Hilde Færevik
KHKristine Holbø
Kristine Holbø
RNRagnhild Nesbakken
Ragnhild Nesbakken
JRJarl Reitan
Jarl Reitan
MTMaria Suong Le Thi
Maria Suong Le Thi
Phase-change materials (PCM) can be used to reduce thermal stress and improve thermal comfort for workers wearing protective clothing. The aim of this study was to investigate the effect of PCM in protective clothing used in simulated work situations. We hypothesized that it would be possible to optimize cooling performance with a design that focuses on careful positioning of PCM, minimizing total insulation and facilitating moisture transport. Thermal stress and thermal comfort were estimated through measurement of body heat production, body temperatures, sweat production, relative humidity in clothing and subjective ratings of thermal comfort, thermal sensitivity and perception of wetness. Experiments were carried out using 2 types of PCM, the crystalline dehydrate of sodium sulphate and microcapsules in fabrics. The results of 1 field and 2 laboratory experimental series were conclusive in that reduced thermal stress and improved thermal comfort were related to the amount and distribution of PCM, reduced sweat production and adequate transport of moisture.

1 July 2019 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Open access
TKTore Kolås
Tore Kolås
ARArne Røyset
Arne Røyset
MGMathieu Grandcolas
Mathieu Grandcolas
MCMattijs Ten Cate
Mattijs Ten Cate
ALAnica Lacau
Anica Lacau

20 February 2015 in Optics Letters
Verified
Journal Article
Closed access
PDF file
JRJ. Romann
J. Romann
JVJ.-C. Valmalette
J.-C. Valmalette
ARA. Røyset
A. Røyset
MEM.-A. Einarsrud
M.-A. Einarsrud
Optical properties of single diatom frustule valves from two different Coscinodiscus species (C. wailesii and C. centralis) are studied by transmission confocal hyperspectral imaging and numerical calculations. Light convergence, concentration, and trapping effects are observed and depend on both the wavelength and the valve orientation. These effects seem to occur independently of the incident light angle. From our results, a wavelength-dependent multifocal lens behavior can be explained by light diffraction related to the radial symmetry of the multiscaled 3D nanostructure.

29 April 1994 in Electronics Letters
Verified
Journal Article
Closed access
ARA. Røyset
A. Røyset
LBL. Bjerkan
L. Bjerkan
DMD. Myhre
D. Myhre
LHL. Hafskjær
L. Hafskjær
The small signal power modulation transfer function in dispersive optical fibre has been used to characterise chirp in semiconductor lasers. Experimental results on three different lasers reveal good agreement between measurements and modelling. The measurement method is simple and accurate.