6 July 2022 in IEEE Transactions on Power Electronics
This article proposes a modified deadbeat predictive current control (M-DPCC) method to improve the dynamic performance of permanent magnet synchronous motor (PMSM). Classical DPCC only predicts one control cycle of the PMSM, which restricts the dynamic performance since multiple control cycles are required for the transient state under heavy load and rated speed working condition. The proposed M-DPCC extends the single-step prediction to the entire dynamic interval in the transient state, by which the comprehensive optimization on the angle of the stator voltage vector can be implemented. Moreover, M-DPCC performed multi-step deadbeat calculation to keep the computation modest. To verify the effectiveness of the proposed M-DPCC, transient-state performance of PMSM using the M-DPCC method, the modulated model predictive control and classical DPCC are explored under a wide range of working condition. Comparative simulation and experimental results indicate that dynamic performance of the PMSM can be improved, especially under rated speed and heavy load conditions. Besides, the parameter sensitivity to inductance mismatch of the three methods is carried out. The stable operation range of the M-DPCC under inductance mismatch is larger than the other two methods. Moreover, the computation complexity of the three methods were investigated. The M-DPCC acquired less computation time than the modulated model predictive control.
16 September 2021 in IEEE Transactions on Energy Conversion
This paper proposed a hybrid subdomain model (HSM) for calculating the magnetic field distribution of interior permanent-magnet (IPM) machine accounting for slotting effect, rotor saliency, and iron nonlinearity. In the constant permeability region, i.e., slots, slot-opening, and air-gap, three subdomains are introduced to represent their magnetic field. By applying the subdomains interface conditions and nonlinear boundary conditions, the analytical air-gap field solution can be obtained based on the governing Laplace and Poisson equation. For the iron region, the magnetic reluctance network (MRN) is proposed to account for rotor saliency iron and nonlinearity. The magnetic voltage source is introduced to represent the permanent-magnet (PM) while the air-gap flux source is used to replace the air-gap reluctance network, which is the key to guarantee the computational efficiency and high accuracy. The electromagnetic performances of both flat-shaped and V-shaped IPM machines are investigated to show the advantages of different IPM machine topologies analytically. The HSM predictions for both IPM machines are validated by finite-element (FE) analysis and experimental results.
1 April 2022 in IEEE Transactions on Transportation Electrification
This article presents an analytical model to predict the performance of eccentric surface-mounted permanent-magnet (ESPM) motor based on the nonlinear conformal mapping and reluctance network hybrid model (NCRHM). The proposed model can reveal the mutual influence of rotor eccentricity on the stator slotting and iron saturation accounting for the distortion of the equivalent current positions and air-gap path among the conformal mappings. The transformation between magnetic voltage drop of iron and equivalent current in the air region (including air-gap and slot region) is employed to consider the increased iron saturation due to the reduced air-gap length. Based on the proposed model, the electromagnetic performance including flux linkage, back electromotive force (EMF), torque, and unbalanced magnetic force (UMF) can be accurately predicted for any kind of rotor eccentricity. In addition, the NCRHM is compared with the complex permeance model (CPM) neglecting both iron saturation and the field distortion in conformal mappings, which exhibits the great advantage of NCRHM for ESPM motor. The excellent accuracy and great efficiency of the proposed model are validated by both finite-element analysis and test results.
13 September 2022 in IEEE Transactions on Power Electronics
This article presents an online method to acquire the stator inductance and flux linkage for inverter-fed surface-mounted permanent magnet synchronous motors (SPMSMs) using switching state functions instead of average models. Given the switching state functions when different voltage vectors are applied to the motors, the information of inductance and flux linkage is revealed. Based on the dc bus voltage and current derivatives obtained from either hardware methods like Rogowski coil and differential circuit, or software methods such as tracking differentiator, stator inductance, and flux linkage are able to be figured out directly using the redundant or more practical methods with the help of recursive least square (RLS). Simulations and experiments are carried out to prove the effectiveness of the proposed methods, besides, dc voltage and operating speed variation as well as the impact of resistance are taken into account. Finally, compared with the conventional parameter identification based on the average models either in α – β or d – q coordinate, the proposed methods with switching state functions have remarkable advantages especially when the rotor position error exists. What needs further effort is the challenging case at very low speed, e.g., it is hard to identify flux linkage due to the small back electromotive force (EMF).
27 June 2023 in IEEE Transactions on Transportation Electrification
This paper presents a comprehensive method to predict the electromagnetic losses in surface-mounted permanent-magnet motors based on a hybrid analytical model. Hybrid analytical model will significantly improve the calculation speed compared with finite-element method while keeping great accuracy, making it a competitive alternative for the analysis and optimization of permanent-magnet motors. As the accurate field distribution is the bias of electromagnetic losses prediction, the magnet loss, sleeve loss, and copper loss can all be accurately obtained from their vector potential distribution using hybrid analytical model with small computational burden. As for iron loss, the improved Jiles-Atherton model is proposed to build the relationship between the loss and the magnetic field in the iron region from the perspective of energy conversion. The predictions of magnet loss, sleeve loss, and copper loss using hybrid analytical model agree well with the finite-element method. The experiment on surface-mounted permanent-magnet prototype demonstrates the high accuracy of iron loss calculation using the combination of the improved Jiles-Atherton model and hybrid analytical model.
7 June 2023 in IEEE Transactions on Transportation Electrification
With the trend toward transportation electrification, the power density of electrical machines faces ever-increasing requirement owing to the stringent limit of weight, especially for aerospace applications. Conventionally, the reliability of electrical machines in such safety-critical application is guaranteed by considerable safety margins, i.e., the over-engineering approach, which prevents electrical machines from reaching higher power densities and leads to a design conflict. This paper proposes a reliability-oriented design approach for low-voltage electrical machines by integrating model-based lifetime prediction into a multi-objective optimization process. Accelerated thermal degradation tests are carried out on mainwall insulation and turn insulation, then the thermal degradation model is built to predict the lifetimes, accordingly. Thermal lifetime models are developed at several lifetime percentiles for both continuous duty and variable duty applications. Finally, a feasible reliability-oriented multi-objective optimization platform is established, based on which a study-case electrical machine for aerospace application is designed and optimized. The prototype is manufactured to verify the optimized performances.