Jaehwan Lee

Jaehwan Lee

Auto-generated profile, based on publicly available information

Jaehwan Lee

Department of Smart Manufacturing Engineering, Changwon National University, Changwon, Gyeongsangnam-do, South Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 April 2020 in Energies
Verified
Journal Article
Open access
PDF file
JLJaehwan Lee
Jaehwan Lee
DKDongmin Kim
Dongmin Kim
JMJeongmin Mun
Jeongmin Mun
SKSeokho Kim
Seokho Kim
Infrared detectors on satellites and spacecraft require cooling to increase their measurement sensitivity. To efficiently cool infrared detectors in a zero gravity environment and in limited spaces, a cryogenic loop heat pipe (CLHP) can be used to transfer heat over a certain distance by the capillary forces generated from porous wicks without a mechanical power source. The CLHP presented in this study transfers the heat load to a condenser 0.5 m away from an evaporator at temperatures below −150 °C. The CLHP with two evaporators includes a subloop for initial start-up, and uses a pressure reduction reservoir (PRR) for the supercritical start-up from room to cryogenic temperature. Nitrogen is used as the working fluid to verify the thermal behavior of the CLHP, and the heat-transfer capacity according to the nitrogen charging pressure of the PRR is investigated. To simulate a cryogenic environment, the CLHP is installed inside a space environment simulator, including a single-stage GM (Gifford McMahon) cryocooler to cool the condenser. The CLHP is horizontally installed to simulate zero gravity. The heat-transfer characteristics are experimentally evaluated through the loop circulation of the CLHP.

3 March 2021 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
JLJaehwan Lee
Jaehwan Lee
JMJeongmin Mun
Jeongmin Mun
JKJunil Kim
Junil Kim
SKSeokho Kim
Seokho Kim
No-insulation (NI) winding techniques are widely used in fabricating thermally, mechanically, and electrically robust REBCO magnets. However, NI coils have disadvantages during charging operation, such as charging delay and heat loss due to leakage current. Leakage current can be reduced by increasing contact resistance. Metal-insulation (MI) winding methods are also used by co-winding high-resistive metal insulators between the winding turns of REBCO wires. Although the contact resistance of MI coils can be substantially increased, quantitative estimation of the magnet contact resistance is difficult owing to the dry-contact between the winding turns. Moreover, special care is needed during epoxy impregnation of MI or NI magnets owing to delamination problems induced by the epoxy layer between the winding turns. In this study, a soldered metal insulation (SMI) method is proposed to remove the drawbacks of the MI coil, such as the hardly predictable contact resistance and the delamination issue during conduction cooling applications. The SMI coils were wound using a tin-plated stainless-steel (SS) tape between the REBCO wires as in the MI coil and they were heated in a furnace to produce soldered contacts between winding turns. To investigate the electric characteristics, sudden discharge and charge/discharge experiments were conducted at 77 K. In this paper, the test coils were fabricated using the NI, MI, and SMI winding methods and the contact resistance of each coil was investigated. The results show that the SMI winding method can be used to create expected or controllable contact resistance.

11 February 2020 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
JLJaehwan Lee
Jaehwan Lee
GSGeonhang Seo
Geonhang Seo
JMJeongmin Mun
Jeongmin Mun
MPMinwon Park
Minwon Park
SKSeokho Kim
Seokho Kim
A 10 MW class high temperature superconducting (HTS) wind power generator is being developed using REBCO wires for offshore installations. The REBCO coil operates at 35 K and is cooled via forced circulation of helium gas cooled though a heat exchanger in a rotating neon reservoir. Thermal and structural designs should be conducted to ensure that the structure can withstand mechanical stress created by the large torque from the 10 MW power, before building a cryogenic refrigeration system. This paper describes the design of supporting structures and the corresponding thermal characteristics of the HTS magnet. The supporting structure considers Lorentz force in the HTS magnet, fully coupled with an electromagnetic design result of the 10 MW class generator, under full load conditions. To estimate total heat loss, thermal radiation and heat loss at current leads are considered. A thermal analysis combined with cooling channels where the cold helium gas flows is performed to verify if the maximum temperature of the coil meets the design criteria. The analysis and design results are applied to develop a novel “neon-helium hybrid refrigeration system” for the 10 MW HTS wind power generator.

5 May 2022 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
JLJaehwan Lee
Jaehwan Lee
JMJeongmin Mun
Jeongmin Mun
JKJunil Kim
Junil Kim
KSKideok Sim
Kideok Sim
SHSeungyong Hahn
Seungyong Hahn
SKSeokho Kim
Seokho Kim
The no-insulation (NI) winding method has been widely used in the fabrication of superconducting coils owing to its excellent thermal stability and mechanical stiffness. In the NI coil, there is a charging delay and heat loss due to leakage current. Therefore, the metal insulated (MI) winding method was proposed to reduce the charging delay and the heat loss due to the leakage current and the increased contact resistance by the metal tape. However, it is difficult to quantify the contact resistance between the turns of the coil during the design stage. To resolve this problem, a new winding method, called soldered metal insulation (SMI), was proposed by the authors, and the electrical properties were evaluated in a bath of liquid nitrogen. As a follow-up to the previous research, experimental investigations were conducted in a conduction cooling test apparatus to investigate the electrical and thermal characteristics of the SMI coil below 77 K. The electric contact resistances were evaluated through sudden discharge experiments. Then, the thermal contact resistances were measured using a heater installed on the outer turn of the coil. It is believed that the SMI winding technique can be applied to fabricate rare-earth barium copper oxide (REBCO) coils with predictable electrical and thermal contact resistances.

6 February 2024 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
SPSihyun Park
Sihyun Park
SHSeungyong Hahn
Seungyong Hahn
UBUijong Bong
Uijong Bong
JYJonghoon Yoon
Jonghoon Yoon
SKSeokho Kim
Seokho Kim
YHYoung Jin Hwang
Young Jin Hwang
This paper examines the electrical characteristics of no-insulation (NI) high-temperature superconducting (HTS) coils impregnated with an electrically conductive epoxy. The NI winding technique refers to a method of winding HTS coils without insulating materials between the winding turns and is regarded as the most promising method to protect the HTS coils from the quench phenomenon. Thus far, many analytical and experimental studies focusing on the electrical characteristics of NI HTS coils have been conducted. From these studies, the quench tolerance levels of NI HTS coils were verified, and the possibility of using NI HTS coils in high-field-magnet applications was confirmed. In addition, studies have recently attempted to apply NI HTS coils to electrical rotating machines. The use of NI HTS coils as field coils in electrical rotating machines is expected to enhance their thermal/electrical stability, but there may also be technical issues related to charging/discharging delays and mechanical reliability. In this paper, we propose a NI HTS coil impregnated with an electrically-conductive epoxy to resolve these issues. In the proposed method, a commercially available epoxy resin is mixed with electrically conductive particles, after which HTS coils are wet-wound using the electrically conductive epoxy. In addition, it was confirmed in charging/discharging tests and in a quench test that HTS coils manufactured by the proposed method show reduced charging/discharging delay times in conjunction with quench-tolerant characteristics. The results here demonstrate the potential of the proposed electrically conductive epoxy impregnated NI HTS coil for electrical rotating machine applications.

8 February 2022 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
QLQuanyue Liu
Quanyue Liu
SLSangjin Lee
Sangjin Lee
JLJaehwan Lee
Jaehwan Lee
JMJeongmin Mun
Jeongmin Mun
JKJunil Kim
Junil Kim
SKSeokho Kim
Seokho Kim
This study analyzes the quench behavior of No-insulation (NI) REBCO pancake. An quench analysis simulation model considering the complex critical current density distribution was developed and validated experimentally. The developed model includes an equivalent circuit model, a thermal model, a magnetic model, and a magnet critical current estimation model. The simulation model is based on a co-simulation using MATLAB and COMSOL, considering the balance of accuracy and computation time. The lumped parameter of the NI magnet was used to solve the governing equations of the equivalent circuit module and thermal module in MATLAB. To accurately calculate the non-uniform electromagnetic field distribution over the coil, a magnetic finite element method was used in COMSOL. A neural network was used to predict the temperature-field-angle dependent magnet critical current. Considering the numerical convergence at different over-current phases, adaptive simulation was used to reduce the total simulation time. The quench behavior was analyzed using the proposed model, and the results were verified experimentally. The simulation results showed that when the azimuthal current is greater than the magnet critical current, it will gradually saturate and approach the magnet critical current, and then decrease at a similar speed. The rate of decrease is equal to the rate of decrease of the magnet critical current. Through the analyses, the corresponding sudden-discharging behavior was simulated and analyzed. The proposed model can be used to perform the post-quench and sudden discharging analyses of pancake coil and has promising applications in multi-pancake post-quench studies.