16 June 2022 in Journal of Applied Physics
Electrical percolation in two-phase materials involves a very singular behavior, manifested as a huge change in the electrical conductivity, for a given volume or mass fraction of the phase with higher conductivity. In contrast, in the case of heat transfer, in two-phase composite systems, analogous percolative phenomena are far more elusive and have been rather difficult to observe in various physical systems. In this Perspective, we present a critical analysis of experimental results and the application of theoretical models aimed to study the effects of percolation phenomena on the thermal and electrical properties of two-phase materials. Our attention will be focused on composites made of high conductivity particles in a polymeric matrix. The effect of several factors, such as the geometrical and physical characteristics of fillers and their connectivity with the matrix, the proportion between the conductivity of filler and the matrix, as well as the crucial role of interfacial thermal resistance, is considered. In particular, the differences between the thermal and electrical thresholds and the physical and geometrical conditions that should be fulfilled to observe thermal percolation are discussed. Future trends, to be followed in the development of new materials, in order to enhance the thermal conductivity as well as in making the thermal percolative effects notable, based on including additional phases and 2D fillers, are also discussed.
16 January 2025 in ACS Applied Energy Materials
DPDiecenia Peralta-Domínguez
Diecenia Peralta-Domínguez
WPWendy Yaznay Padrón-Hernández
Wendy Yaznay Padrón-Hernández
+8
Hybrid lead halide perovskite solar cells (PSCs) stand out in terms of their high efficiency, yet the limited stability and process scalability pose challenges to their commercialization. Fully printable carbon-based perovskite solar cells (C-PSCs), consisting of a triple stack of mesoporous titania, zirconia, and carbon layers impregnated with the perovskite material, have been introduced as an attractive architecture; however, they generally exhibit lower efficiency. This study proposes a viable and scalable approach to increase the efficiency of C-PSCs by incorporation of an intermediate layer of mesoporous, nanostructured NiCo2O4 between the zirconia and carbon layers. The devices show an average increase in power conversion efficiency from 7.9 to 11%, with a champion device efficiency of 12.4%, associated with an enhanced average open-circuit voltage (V OC) from 0.869 to 0.962 V. Electrochemical impedance spectroscopy reveals that the high-frequency recombination resistance (R HF) decreases exponentially with V OC with the same slope as for the reference triple-stack system, indicating that the mechanism is unchanged; however, a substantial increase in R HF is observed. These results indicate that the hole extraction efficiency improves upon incorporation of the NiCo2O4 film thus decreasing surface recombination at the nonselective carbon contact. On the other hand, we postulate a possible contribution of the high capacitance of the interlayer, which may result in a shift of the Fermi energy of the carbon electrode and play a role in the hysteresis in the current - voltage curve.
25 April 2023 in Physica Status Solidi (RRL) – Rapid Research Letters
In materials science, the knowledge of the thermal properties of thin films on thick substrates is crucial in determining the role of the film in the physical properties of the entire system. Even though the role of the film can be very important, the determination of its thermal properties is a challenging task due to the fact that its contribution to heat transfer is generally hard to single out from the influence of the substrate. Herein, a simple analytical methodology, based on the photoacoustic technique, useful in the thermal characterization of thin films on thick substrates, is presented. The approach is based on illuminating one side of the substrate with a modulated laser beam and monitoring the thermal contrast when a thin film is formed on the opposite side. This methodology allows to unambiguously determine the volumetric heat capacity of micrometric polymeric thin films. The limits of applicability of the method as well as the possibility of performing a full characterization of the thermal properties of the film are discussed.
1 September 2019 in Materials Research Express
This work reports on a study of light transmission in electrically responsive materials consisting of long aspect ratio carbon nanostructures in fluid matrices. Composite fluids were prepared using multiwalled carbon nanotubes or carbon nanofibers in two types of fluid matrices, ethylene glycol and distilled water. Measurements were performed illuminating the sample with polarized light. Before, during and after applying a uniform and constant electric field, the evolution of the intensity of the transmitted light was monitored. For ethylene glycol-based dispersions, it was found that the applied electric field induces substantial changes in the polarization component of the incident light parallel with the electric field vector. In contrast, for the same dispersions, the optical transmission of the light polarized in the direction perpendicular to the electric field does not show appreciable changes. The matrix fluid properties were found to be crucial for the electro-optical effect: in distilled water-based dispersions, no changes of transmission were found upon applying an electric field for any of the polarization components of the light. It was also shown that the polarization of the transmitted light can be dynamically adjusted in time and space by varying the applied voltage across ethylene glycol dispersions. The electric control of the light polarization opens the possibility of using these simple systems as light dimmers or in a more sophisticated application such as reversible dynamic polarizers.
17 April 2026 in Solar Energy Materials and Solar Cells
BHBeatriz E. Heredia-Cervera
Beatriz E. Heredia-Cervera
+17
18 August 2026 in ACS Omega
RRRaúl Pareja RodrígUez
FAFernando Cervantes Alvarez
Fernando Cervantes Alvarez
+3
Addressing the urgent need to convert biomass waste into high-value functional materials, this study presents the synthesis of a sustainable ternary photocatalyst: ZnO-MIL-101(Fe)/Graphene-like carbon (ZMG). A central feature of this design is the strategic derivation of the graphene-like carbon (GLC) component from the abundant invasive biomass Phragmites australis, thereby aligning with Circular Economy principles. We evaluated the composite’s efficiency through the degradation of Methyl Orange (MO) under natural sunlight. Comparative evaluations demonstrated the superior performance of the ZMG system, achieving 85% MO removal under natural sunlight within 90 min, significantly surpassing the activity of both the individual components and binary composite. This enhanced activity is fundamentally due to an optimized synergistic relationship and an interfacial mechanism that ensures highly efficient charge-carrier separation. Under laboratory UV irradiation, the photocatalytic activity demonstrated excellent kinetics, achieving complete MO removal within 60 min and yielding the highest rate constant (κ = 0.070 min–1). Furthermore, the ZMG maintained excellent structural stability, with removal efficiency exceeding 96% after four consecutive reuse cycles. These findings validate the ZMG as a kinetically robust, sustainable, and highly effective candidate for practical wastewater remediation applications.