CARYS WORSLEY

Ms. CARYS WORSLEY

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2021 in Materials Advances
Verified
Journal Article
Open access
PDF file
CWCARYS WORSLEY
CARYS WORSLEY
DRD. Raptis
D. Raptis
SMSimone Meroni
Simone Meroni
RPR. Patidar
R. Patidar
APA. Pockett
A. Pockett
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
Green solvent mixes are applied in printed mesoscopic perovskite solar cells and modules, achieving 13.8% PCE at 1 cm 2 and >9% PCE in a 220 cm 2 module. This shows how green solvent engineering can aid improvement and scale-up in emerging technologies.

12 January 2021 in Energies
Verified
Journal Article
Open access
PDF file
SMSimone Meroni
Simone Meroni
CWCARYS WORSLEY
CARYS WORSLEY
DRDimitrios Raptis
Dimitrios Raptis
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
Perovskite solar cells (PSCs) have already achieved comparable performance to industrially established silicon technologies. However, high performance and stability must be also be achieved at large area and low cost to be truly commercially viable. The fully printable triple-mesoscopic carbon perovskite solar cell (mCPSC) has demonstrated unprecedented stability and can be produced at low capital cost with inexpensive materials. These devices are inherently scalable, and large-area modules have already been fabricated using low-cost screen printing. As a uniquely stable, scalable and low-cost architecture, mCPSC research has advanced significantly in recent years. This review provides a detailed overview of advancements in the materials and processing of each individual stack layer as well as in-depth coverage of work on perovskite formulations, with the view of highlighting potential areas for future research. Long term stability studies will also be discussed, to emphasise the impressive achievements of mCPSCs for both indoor and outdoor applications.

3 April 2024 in Materials Advances
Verified
Journal Article
Open access
PDF file
CWCARYS WORSLEY
CARYS WORSLEY
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
DHDeclan Hughes
Declan Hughes
WTWing Chung Tsoi
Wing Chung Tsoi
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
Screen-printed perovskite devices made using green γ-valerolactone precursors are found to improve significantly following fabrication due to slow residual solvent loss over time. This is also observed in large-scale 220 cm2 modules.

9 April 2024 in Advanced Functional Materials
Verified
Journal Article
Open access
PDF file
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
RBRebecca Bolton
Rebecca Bolton
Tom DunlopTom Dunlop
Tom Dunlop
KLKathryn Lacey
Kathryn Lacey
CWCARYS WORSLEY
CARYS WORSLEY
EJEifion Jewell
Eifion Jewell
Mesoscopic carbon‐based perovskite solar cells (C‐PSCs) have the potential to be manufactured at an industrial scale by utilizing screen‐printing, a simple, affordable, and commercially mature process. As such, many recent publications have focused on enhancing performance through modifying cell architecture and perovskite chemistries. This work examines how ink rheology can be tuned to optimize cell performance through reducing the occurrence of common print defects to create higher quality m‐TiO2 films. Inks with different solvent dilutions and rheological profiles are assessed using high‐speed imaging through the screen‐printing visualization (SPV) technique, to investigate the impact of the viscosity and elasticity on ink separation mechanisms. The resultant film quality and its influence on device performances are then assessed. Ink separation lengths are minimized, and the formation of filaments ceases during printing, leading to improved TiO2 film topography and homogenous infiltration of the perovskite precursor. Consequently, PCE is improved by over 10% of the original efficiency in cells and 224 cm2 active area modules due to enhanced Voc and FF. These results not only provide key insights into tailoring ink rheology, to achieve improved print homogeneity and higher performing cells, but also aid further work on enhancing the performance of other screen‐printed functional films.

24 February 2024 in ACS Applied Energy Materials
Verified
Journal Article
Open access
CWCARYS WORSLEY
CARYS WORSLEY
TDThomas O. Dunlop
Thomas O. Dunlop
SPSarah-Jane Potts
Sarah-Jane Potts
RGRodrigo Garcia-Rodriguez
Rodrigo Garcia-Rodriguez
RBRebecca S. Bolton
Rebecca S. Bolton
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
Mesoscopic carbon-based perovskite solar cells (CPSCs) are often cited as a potential frontrunner to perovskite commercialization. Infiltration, the extent to which perovskite fills the mesoporous scaffold, is critical for optimum performance and stability. However, infiltration data are usually presented as qualitative photographic comparisons of samples with extreme infiltration variation. This work examines how small infiltration defects impact performance using an optical microscopy examination of the base TiO2 layer to identify issues and develop targeted techniques for infiltration enhancement. Critically, the uninfiltrated area at the base of the stack was found to correlate well with PCE across multiple batches of varied print quality and ZrO2 thickness. Through reduction of mesh mark defects and improvement of print quality in the ZrO2 and carbon layers, a champion PCE of 15.01% is attained. It follows that this facile, multiscaled, nondestructive technique could enable targeted performance enhancement and quality control in future scale-up initiatives.

1 June 2022 in Solar
Verified
Journal Article
Open access
PDF file
DRDimitrios Raptis
Dimitrios Raptis
CWCARYS WORSLEY
CARYS WORSLEY
SMSimone Meroni
Simone Meroni
APAdam Pockett
Adam Pockett
MCMatthew Carnie
Matthew Carnie
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
Fully printable carbon-based perovskite solar cells (C-PSCs) represent some of the most promising perovskite solar cell (PSC) architectures. Highly scalable, stable, and low in cost—these devices consist of a TiO2 compact layer (C-TiO2) and three sequentially screen-printed mesoporous layers of TiO2, ZrO2, and carbon, through which perovskite is infiltrated. While there has been remarkable progress in optimizing and scaling up deposition of mesoporous layers and perovskite, few publications have focused on optimizing C-TiO2. In this work, we investigate the potential for substituting commonly used spray pyrolysis with more easily scaled screen-printing. It was found that when comparing layers of similar thickness, 1 cm2 devices fabricated with printed C-TiO2 exhibited similar power conversion efficiency (PCE) to those fabricated with spray pyrolysis. In contrast, thicker-printed C-TiO2 led to lower efficiency. The influence of TiCl4 treatment on the quality of produced compact layers was also examined. This proved beneficial, mostly in the printed films, where a champion PCE of 13.11% was attained using screen-printed, TiCl4 treated C-TiO2. This work proves that screen-printing is a viable replacement for spray pyrolysis in C-PSCs fabrication.