Basar Ozkan

Basar Ozkan

Auto-generated profile, based on publicly available information

Basar Ozkan

Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough LE11 3TU, UK

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2022 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
BOBasar Ozkan
Basar Ozkan
FSFarzaneh Sameni
Farzaneh Sameni
FBFloriana Bianchi
Floriana Bianchi
HZHanifeh Zarezadeh
Hanifeh Zarezadeh
SKSarah Karmel
Sarah Karmel
ESEhsan Sabet
Ehsan Sabet

23 July 2022 in Polymers
Verified
Journal Article
Open access
PDF file
FSFarzaneh Sameni
Farzaneh Sameni
BOBasar Ozkan
Basar Ozkan
HZHanifeh Zarezadeh
Hanifeh Zarezadeh
SKSarah Karmel
Sarah Karmel
DEDaniel Engstrom
Daniel Engstrom
ESEhsan Sabet
Ehsan Sabet
In the vat photopolymerisation 3D printing technique, the properties of the printed parts are highly dependent on the degree of conversion of the monomers. The mechanisms and advantages of vat photopolymerisation at elevated temperatures, or so called “hot lithography”, were investigated in this paper. Two types of photoresins, commercially used as highly accurate castable resins, with different structural and diluent monomers, were employed in this study. Samples were printed at 25 °C, 40 °C, and 55 °C. The results show that hot lithography can significantly enhance the mechanical and dimensional properties of the printed parts and is more effective when there is a diluent with a network Tg close to the print temperature. When processed at 55 °C, Mixture A, which contains a diluent with a network Tg = 53 °C, was more readily impacted by heat compared to Mixture B, whose diluent had a network Tg = 105. As a result, a higher degree of conversion, followed by an increased Tg of the diluents, and improvements in the tensile strength and dimensional stability of the printed parts were observed, which enhanced the outcomes of the prints for the intended application in investment casting of complex components used in the aero and energy sectors. In conclusion, the effectiveness of the hot lithography process is contained by a correlation between the process temperature and the characteristics of the monomers in the mixture.

24 July 2023 in Polymers
Verified
Journal Article
Open access
PDF file
OBOzkan Basar
Ozkan Basar
VVVarghese Paul Veliyath
Varghese Paul Veliyath
FTFatih TARAK
Fatih TARAK
ESEhsan Sabet
Ehsan Sabet
Additive ceramics manufacturing with vat-photopolymerisation (VP) is a developing field, and the need for suitable printing materials hinders its fast growth. Binder mixtures significantly influence the mechanical properties of printed ceramic bodies by VP, considering their rheological properties, curing performances and green body characteristics. Improving mechanical characteristics and reducing cracks during printing and post-processes is mainly related to binder formulations. The study aims to develop a binder formulation to provide the printed ceramic specimens with additional green strength. The impact on mechanical properties (ultimate tensile strength, flexural strength, Young’s and strain at breakpoint), viscosity and cure performance of Urethane Acrylate (UA) and thermoplastic Polyether Acrylate (PEA) oligomers to monofunctional N-Vinylpyrrolidone (NVP), 1,6-Hexanediol Diacrylate (HDDA) and Tri-functional Photocentric 34 (PC34) monomers were investigated under varying concentrations. The best mechanical characteristic was showcased when the PC34 was replaced with 20–30 wt.% of UA in the organic medium. The Thermogravimetric Analysis (TGA) and sintering test outcomes revealed that increasing the content of NVP in the organic medium (above 15 wt.%) leads to uncontrolled thermal degradation during debinding and defects on ceramic parts after sintering. The negative effect of UA on the viscosity of ceramic-loaded mixtures was controlled by eliminating the PC34 compound with NVP and HDDA, and optimum mechanical properties were achieved at 15 wt.% of NVP and 65 wt.% of HDDA. PEA is added to provide additional flexibility to the ceramic parts. It was found that strain and other mechanical parameters peaked at 15 wt.% of PEA. The study formulated the most suitable binder formulation on the green body strength of printing silica ceramics as 50 wt.% HDDA, 20 wt.% Urethane Acrylate, 15 wt.% NVP and 15 wt.% PEA.

29 October 2022 in Polymers
Verified
Journal Article
Open access
PDF file
FSFarzaneh Sameni
Farzaneh Sameni
BOBasar Ozkan
Basar Ozkan
SKSarah Karmel
Sarah Karmel
DEDaniel Engstrom
Daniel Engstrom
ESEhsan Sabet
Ehsan Sabet
The material properties and processing of investment casting patterns manufactured using conventional wax injection Molding and those manufactured by vat photopolymerization can be substantially different in terms of thermal expansion and mechanical properties, which can generate problems with dimensional accuracy and stability before and during ceramic shelling and shell failures during the burn-out of the 3D printed casting patterns. In this paper and for the first time, the monofunctional Acryloyl morpholine monomer was used for 3D printing of casting patterns, due to its thermoplastic-like behavior, e.g., softening by heat. However, the hydrophilic behavior of this polymer led to an incorporation of up to 60 wt% of Hexanediol diacrylate, to control the water absorption of the network, which to some extent, compromised the softening feature of Acryloyl morpholine. Addition of a powdered wax filler resulted in a delayed thermal decomposition of the polymer network, however, it helped to reduce the thermal expansion of the parts. The dimensional accuracy and stability of the wax-filled formulation indicated an excellent dimensional tolerance of less than ±130 µm. Finally, the 3D printed patterns successfully went through a burn out process with no damages to the ceramic shell.

15 September 2026 in Materials & Design
Verified
Journal Article
Open access
BOBasar Ozkan
Basar Ozkan
Athanasios GoulasAthanasios Goulas
Athanasios Goulas
SSSina Saremi-Yarahmadi
Sina Saremi-Yarahmadi
BVBala Vaidhyanathan
Bala Vaidhyanathan