This paper was published in the journal Applied Materials Today and the definitive published version is available at http://dx.doi.org/10.1016/j.apmt.2016.11.004.This research paper investigates the suitability of ceramic multicomponent materials, which are found on the Martian and Lunar surfaces, for 3D printing (aka Additive Manufacturing) of solid structures. 3D printing is a promising solution as part of the cutting edge field of future in‐situ space manufacturing applications.\ud 3D printing of physical assets from simulated Martian and Lunar regolith was successfully performed during this work by utilising laser‐based powder bed fusion equipment. Extensive evaluation of the raw regolith simulants was conducted via Optical and Electron Microscopy (SEM), Visible‐Near Infrared/Infrared (Vis‐NIR/IR) Spectroscopy and thermal characterisation via Thermogravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC). The analysis results led to the characterisation of key properties of these multicomponent ceramic materials with regards to their processability via powder bed fusion 3D printing.\ud The Lunar and Martian simulant regolith analogues demonstrated spectral absorbance values of up to 92% within the Vis‐NIR spectra. Thermal analysis demonstrated that these materials respond very differently to laser processing, with a high volatility (30% weight change) for the Martian analogue as opposed to its less volatile Lunar counterpart (<1% weight change). Results also showed a range of multiple thermal occurrences associated with melting, glass transition and crystallisation reactions. The morphological features of the powder particles are identified as contributing to densification limitations for powder bed fusion processing.\ud This investigation has shown that – provided that the simulants are good matches for the actual regoliths – the lunar material is a viable candidate material for powder bed fusion 3D printing, whereas Martian regolith is not
Purpose: The purpose of this paper is to investigate the effect of the main process parameters of laser melting (LM) type additive manufacturing (AM) on multi-layered structures manufactured from JSC-1A Lunar regolith (Moondust) simulant powder. Design/methodology/approach: Laser diffraction technology was used to analyse and confirm the simulant powder material particle sizes and distribution. Geometrical shapes were then manufactured on a Realizer SLM™ 100 using the simulant powder. The laser-processed samples were analysed via scanning electron microscopy to evaluate surface and internal morphologies, X-ray fluorescence spectroscopy to analyse the chemical composition after processing, and the samples were mechanically investigated via Vickers micro-hardness testing. Findings: A combination of process parameters resulting in an energy density value of 1.011 J/mm2 allowed the successful production of components directly from Lunar regolith simulant. An internal relative porosity of 40.8 per cent, material hardness of 670 ± 11 HV and a dimensional accuracy of 99.8 per cent were observed in the fabricated samples. Originality/value: This research paper is investigating the novel application of a powder bed fusion AM process category as a potential on-site manufacturing approach for manufacturing structures/components out of Lunar regolith (Moondust). It was shown that this AM process category has the capability to directly manufacture multi-layered parts out of Lunar regolith, which has potential applicability to future moon colonization.
Fused filament fabrication (FFF) is a well-known and greatly accessible additive manufacturing technology, that has found great use in the prototyping and manufacture of radiofrequency componentry, by using a range of composite thermoplastic materials that possess superior properties, when compared to standard materials for 3D printing. However, due to their nature and synthesis, they are often a great challenge to print successfully which in turn affects their microwave properties. Hence, determining the optimum printing strategy and settings is important to advance this area. The manufacturing study presented in this paper shows the impact of the main process parameters: printing speed, hatch spacing, layer height and material infill, during 3D printing on the relative permittivity (εr), and loss tangent (tanδ) of the resultant additively manufactured test samples. A combination of process parameters arising from this study, allowed successful 3D printing of test samples, that marked a relative permittivity of 9.06 ± 0.09 and dielectric loss of 0.032 ± 0.003.
Additive manufacturing (AM) has become more important and common in recent years. Advantages of AM include the ability to rapidly design and fabricate samples much faster than traditional manufacturing processes and to create complex internal geometries. Materials are crucial components of microwave systems and proper and accurate measurement of their dielectric properties is important to aid a high level of accuracy in design. There are numerous measurement techniques and finding the most appropriate method is important and requires consideration of all different factors and limitations. One limitation of sample preparation is that the sample size needs to fit in the measurement method. By utilizing the advantage of additive manufacturing, the material can be characterized using different measurement methods. In this paper, the additive manufacturing process and dielectric measurement methods have been critically reviewed. The test specimens for measuring dielectric properties were fabricated using fused filament fabrication (FFF)-based additive manufacturing and were measured using four different commercial dielectric properties measurement instruments including split post dielectric resonator (SPDR), rectangular waveguide, TE01δ cavity resonator, and open resonator. The measured results from the four techniques have been compared and have shown reasonable agreement with measurements within a 10 percent range.
1 January 2021 in Journal of the European Ceramic Society