This paper addresses the influence of the static and dynamic laboratory compaction procedures in the compaction curves and mechanical strength of two residual soils from the Zona da Mata Norte, in the state of Minas Gerais, Brazil. The laboratory testing program was directed to: (i) two gneissic residual soils, respectively, with silty-sandy clay and clayey-silty sand textures; (ii) compaction of specimens at the standard Proctor compaction effort and at the optimum water content (wot), as well as at wot - 3% and wot + 2%; (iii) determination of the unconfined compressive strength of the compacted specimens; (iv) micromorphological analysis of thin sections of the compacted specimens using optical microscopy; (v) statistical analysis of the laboratory testing program data. Conclusions are, as follows: (i) there was statistically significant influence of the compaction procedures on the optimum compaction parameters; (ii) for both soils, significant structural changes represented by variations in the unconfined compression strength were observed evidencing the importance of the soils formation processes in their mechanical responses when compacted; and (iii) differences in the soils structures produced by the static and dynamic compaction procedures were identified through incorporation of the micromorphological analysis.
Este trabalho teve como objetivo analisar o comportamento mecânico da mistura de um solo residual jovem de textura predominantemente arenosa reforçado com fibras de polipropileno, com vistas à aplicação em estradas florestais. Como ponto de partida, determinou-se, mediante os resultados de ensaios de compressão não-confinada, realizados em corpos-de-prova compactados na energia do ensaio Proctor Normal, que o quantitativo de 0,75% de fibras com 20 mm de comprimento foi a combinação responsável pelo maior ganho de resistência. Com a mistura solo-fibra composta por essa combinação, foram realizados ensaios triaxiais do tipo CID/Sat em corpos-de-prova compactados na energia anteriormente referida. Através desta pesquisa, foi possível avaliar: (i) a influência da variação da umidade nos parâmetros de resistência mecânica do solo e das misturas solo-fibra e (ii) a influência das fibras nos parâmetros de resistência ao cisalhamento do solo em estudo. Analisando os resultados, pôde-se concluir que o uso de fibras de polipropileno promoveu um ganho da ordem de 110% na resistência à compressão não-confinada e de 560% na coesão de intercepto do solo estudado.
The main objective of this study was to propose the application of soil-lime mixtures asa primary coating layerof unpavedforestroads based on the premise that this layer can be considered mechanically similar to a flexible pavementsub base layer, aiming to fill a gap in the current technical literature and engineering practice in this field of knowledge. In the study, a laboratory test program was carried out in a residual gneiss soil encompassing: (i) geotechnical characterization tests; (ii) compaction tests at the standard Proctor energy on soil specimens and on soil-lime mixturespecimens prepared with lime contents of 2, 4 and 6% related to the dry soil mass; (iii) unconfined compressive strength tests on soil specimens compacted at the standard Proctor optimum parameters; and (iv) unconfined compressive strength tests on specimens of soil-lime mixtures compacted at the standard Proctor optimum compaction parameters with lime contents of 2, 4 and 6%, and cured at 22.8°C in the curing periods of 3, 7, 28 and 90 days. The results showed that the addition of lime resulted in: (i) reduction in soil maximum dry unit weight (gdmax) and increase in soil optimum water content (wopt);and(ii) significant gains in soil unconfined compressive strength that evidenced the expressive occurrence of pozzolanic reactions in the mixtures.Based on the hypothesis of a similar requirement for soil-cement and soil-lime mixtures, the tested soil-lime mixtures met the minimum mechanical strength (1.2MPa) required for application as a primary coating layer of unpaved forest roads.