5 June 2018 in Materials Science Forum
Reliability characterization of SiC devices is an ongoing activity. For this work, 650 V SiC JBS diodes in TO247 housings were tested in H3TRB. After a test period of 4000 hours none of the devices had failed during the test and only two out of sixteen devices had failed during blocking curve measurements performed at intermediate time steps. This is significantly better performance than many silicon devices offer today. The failure spots of the failed devices were detected at the edge of the main junction appearing as semi-circular cavities in the aluminum metallization. All other devices did not even show deviations from their original blocking curves.
6 June 2023 in Materials Science Forum
Silicon carbide (SiC) MOSFETs are gaining more and more market share in typical silicon (Si) IGBT applications such as traction or renewable energies. Especially in reliability sensitive traction applications, medium voltage IGBT-modules (3.3 kV-6.5 kV) are widely used and introducing SiC-MOSFETs to such industries is the next self-evident step already on the way. While their superior electrical performance has been generally accepted already (e.g. [1]), SiC-modules have not yet established a track record of high reliability in this voltage class. For this study, 3.3kV SiC-MOSFET-switches were compared to standard Si-IGBTs regarding their humidity robustness under high voltage bias. Both chip types had been assembled in the same traction rated packages to exclude this influence. The Si-IGBTs resembled the well-known industry standard performance, while the SiC-MOSFETs show no degradation within the reported test time of 2000 h. Given the fact [2], that the latest Si-IGBT generation offers a much better humidity performance as well, the standardised HV-H³TRB is no longer sufficient to provoke failures within a reasonable testing time. On the one hand, this suggests that humidity driven failures will not be an issue under field conditions anymore. On the other hand, even harsher tests are required to investigate differences in humidity performance.
12 January 2024 in Advanced Materials Interfaces
Organically modified layered silicates can be used as barrier pigments in organic coating systems to reduce the permeation of water vapor and gases, e.g., oxygen as well as harmful gases that promote corrosion. Unmodified layered silicates are not sufficient to reduce the permeation significantly. However, the arrangement and orientation of the particles have an enormous impact on the later performance in the barrier film. In organic solvents or non‐aqueous polymer matrices the non‐modified layered silicates cannot exfoliate adequately. The organic modification influences the layer spacing and the compatibility to organic solvents. Layered silicates are modified with dodecylamine to enhance the spacing layer. The spacing layer is enhanced by 55% caused by the organic modification as it is commonly known. In contrast to previous work freeze drying of the organically modified layered silicates improved the particle distribution and by this barrier properties significantly. The modified particles reduce the diffusion of water and oxygen by ≈99.6% and 97.2%, respectively. The corrosive gas test of electronic circuit boards shows no growth of dendrites and no failure of the electronics in contrast to protective coating without the layered silicates.
23 August 2024 in Solid State Phenomena
Recently, silicon carbide (SiC) power modules of the 3.3 kV voltage class became available and are a promising candidate to replace silicon power modules in traction applications. However, the more than three times higher Young’s Modulus compared to silicon leads to a reduced lifetime under thermo-mechanical stress. This could pose a significant obstacle in their implementation, since traction applications are particularly demanding in their mission profiles with respect to load cycling, but also to environmental conditions. Thus, the thermo-mechanical stress is not just limiting the lifetime itself, but might also promote the humidity induced degradation due to delamination or micro-cracks. In this work, multiple power cycling tests at different temperature swings on 3.3 kV SiC MOSFET chips in a power module were performed, to assess their ruggedness under thermo-mechanical stress. Before or afterwards, these modules were tested under standard HV-H3TRB conditions to verify the interaction between thermo-mechanical and humidity stress on the robustness of the modules.
18 May 2026 in Key Engineering Materials
In standard environmental reliability tests, Silicon Carbide (SiC) MOSFETs show a superior performance compared to their Silicon counterparts. This raises the question if the SiC modules are robust and reliable under all circumstances in the field and against all failure mechanisms or only in the standard laboratory tests. The HV-H³TRB (High Voltage – High Humidity High Temperature Reverse Bias) test is the standard test for humidity reliability and SiC modules survive this test for several thousand hours, easily surpassing the 1,000 h qualification requirement. However, in field service the devices are exposed to steep voltage slopes (high dv/dt) instead of the DC voltage stress applied in a standard HV-H³TRB. In this work, a dynamic HV-H³TRB test was performed on 3.3 kV SiC MOSFET modules for more than 4,000 h with switched high voltages of 80% V nom , only observing minor degradations and reversible blocking capabilities.