Ce1−xZrxO2 oxides (x = 0.1, 0.25, 0.5) prepared via the Pechini route were investigated using XRD analysis, N2 physisorption, TEM, and TPR in combination with density functional theory calculations. The Ni/Ce1−xZrxO2 catalysts were characterized via XRD analysis, SEM-EDX, TEM-EDX, and CO chemisorption and tested in carbon dioxide methanation. The obtained Ce1−xZrxO2 materials were single-phase solid solutions. The increase in Zr content intensified crystal structure strains and favored the reducibility of the Ce1−xZrxO2 oxides but strongly affected their microstructure. The catalytic activity of the Ni/Ce1−xZrxO2 catalysts was found to depend on the composition of the Ce1−xZrxO2 supports. The detected negative effect of Zr content on the catalytic activity was attributed to the decrease in the dispersion of the Ni0 nanoparticles and the length of metal–support contacts due to the worsening microstructure of Ce1−xZrxO2 oxides. The improvement of the redox properties of the Ce1−xZrxO2 oxide supports through cation modification can be negated by changes in their microstructure and textural characteristics.
1 November 2021 in Materials Chemistry and Physics
Synthesis and study of materials based on bismuth cerates and titanates were carried out. Complex oxides Bi1.6Y0.4Ti2O7 were synthesized by the citrate route; Bi2Ce2O7 and Bi1.6Y0.4Ce2O7—by the Pechini method. The structural characteristics of materials after conventional sintering at 500–1300 °C were studied. It is demonstrated that the formation of a pure pyrochlore phase, Bi1.6Y0.4Ti2O7, occurs after high-temperature calcination. Complex oxides Bi2Ce2O7 and Bi1.6Y0.4Ce2O7 have a pyrochlore structure formed at low temperatures. Yttrium doping of bismuth cerate lowers the formation temperature of the pyrochlore phase. As a result of calcination at high temperatures, the pyrochlore phase transforms into the CeO2-like fluorite phase enriched by bismuth oxide. The influence of radiation-thermal sintering (RTS) conditions using e-beams was studied as well. In this case, dense ceramics are formed even at sufficiently low temperatures and short processing times. The transport characteristics of the obtained materials were studied. It has been shown that bismuth cerates have high oxygen conductivity. Conclusions are drawn about the oxygen diffusion mechanism for these systems. The materials studied are promising for use as oxygen-conducting layers in composite membranes.
Methane oxidative coupling (OCM) is considered a potential direct route to produce C2 hydrocarbons. Layered perovskite-like Sr2TiO4 is a promising OCM catalyst. Mechanochemical activation (MA) is known to be an environmentally friendly method for perovskite synthesis. Sr2TiO4 were synthesized using MA of the mixtures containing SrCO3 or SrO and TiO2 or TiO(OH)2 and annealing at 900 and 1100 °C. XRD and FT-IRS showed that MA leads to the starting component disordering and formation of SrTiO3 only for SrO being pronounced when using TiO(OH)2. After annealing at 900 °C, Sr2TiO4 was mainly produced from the mixtures of SrCO3 or SrO and TiO(OH)2. The single-phase Sr2TiO4 was only obtained from MA products containing SrCO3 after calcination at 1100 °C. The surface enrichment with Sr was observed by XPS for all samples annealed at 1100 °C depending on the MA product composition. The OCM activity of the samples correlated with the surface Sr concentration and the ratio of the surface oxygen amount in SrO and perovskite (Oo/Op). The maximal CH4 conversion and C2 yield (25.6 and 15.5% at 900 °C, respectively), and the high long-term stability were observed for the sample obtained from (SrCO3 + TiO2), showing the specific surface morphology and optimal values of the surface Sr concentration and Oo/Op ratio.