Ole Christian Spro

Ole Christian Spro

Auto-generated profile, based on publicly available information

Ole Christian Spro

Norwegian University of Science and Technology (NTNU), Trondheim, Norway

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 February 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
OSOle Christian Spro
Ole Christian Spro
PLPierre Lefranc
Pierre Lefranc
SPSanghyeon Park
Sanghyeon Park
JRJuan M. Rivas-Davila
Juan M. Rivas-Davila
DPDimosthenis Peftitsis
Dimosthenis Peftitsis
TUTore Undeland
Tore Undeland

5 January 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
OSOle Christian Spro
Ole Christian Spro
FMFrank Mauseth
Frank Mauseth
DPDimosthenis Peftitsis
Dimosthenis Peftitsis
This article investigates the insulation design for printed, planar, coreless, and high-frequency transformers with high isolation-voltage. By using finite element analysis on 2-D axial-symmetry, the transformer circuit parameters and electric field distribution are modeled and estimated. Several transformers are designed for an operating frequency of 6.78 MHz. The high frequency, coreless design allows for using thicker insulation material while ensuring a high transformer efficiency. The inclusion of the coupling capacitance in the design optimization results in several design solutions with the same figure of merit, but with different footprint and isolation voltages. Moreover, high electric fields are identified around the sharp edges of the printed circuit board (PCB) windings. Finally, the electrical and isolation performance is verified experimentally. The measured electrical properties are close to the simulated values, validating the chosen model. Breakdown tests demonstrate the feasibility of isolation voltage levels up to several tens of kilovolts. The majority of breakdowns occurs at the outer edge of the PCB winding that was identified as a high-field area. Additionally, a concept for grading the electric field of PCB windings is also proposed. Based on the results, the design aspects are discussed in detail for planar, high-frequency isolation transformers with medium-voltage isolation level.

28 July 2020 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
HHHaavard Lefdal Hove
Haavard Lefdal Hove
OSOle Christian Spro
Ole Christian Spro
GGGiuseppe Guidi
Giuseppe Guidi
DPDimosthenis Peftitsis
Dimosthenis Peftitsis
This paper presents improvements to a SPICE model for a commercially available SiC MOSFET to avoid convergence errors while still providing reliable simulation results. Functionality in the internal part of the model that shapes the transconductance of the device according to its junction temperature and gate-source voltage dependency has been improved to provide a continuous characteristic rather than the initial discontinuous performance. Furthermore, the output characteristics from the initial and the proposed model have been compared to lab measurements of an actual device. The results show that the proposed and initial model provide equally reliable simulation results. However, the proposed model does not run into convergence problems.

1 May 2019
Verified
Conference Paper
Open access
HHHavard Lefdal Hove
Havard Lefdal Hove
OSOle Christian Spro
Ole Christian Spro
DPDimosthenis Peftitsis
Dimosthenis Peftitsis
GGGiuseppe Guidi
Giuseppe Guidi
KLKjell Ljokelsoy
Kjell Ljokelsoy
This paper presents a voltage-controlled multistage gate driver topology for delay time minimization that improves the converter output voltage quality while supplying a motor load. Three gate driver topologies for SiC MOSFETs are compared based on their dead time requirement in a bridge leg converter. Experimental results of the gate driver delay times are reported and are used as input to a simulated motor drive application. Results show that turn-off delay times can be reduced by up to 74 % for the multistage driver compared to the conventional counterpart when the rate of change for the converter voltage output is limited to 10 V/ns. Furthermore, minimizing the dead time increases the linearity region of the output voltage from the converter by 1.8 % to 3.8 % and reduces the current THD in the linear region by up to 7.7 % when switching at 15kHz.

18 July 2021
Verified
Conference Paper
Closed access
CLChendan Li
Chendan Li
OSOle Christian Spro
Ole Christian Spro
Olav FossoOlav Fosso
Olav Fosso
Lifetime is an important indicator of system reliability. With the paradigm power system evolves into a power electronics based power system, lifetime modelling method for power electronics needs to be revisited and perspective for modelling power electronics lifetime for system planning and operation usage is worth looking at. In this paper, the existent methods for modelling lifetime for power electronic system are reviewed and classified. The purpose of the paper is to give a brief overview of different modeling methods for power electronics lifetime, and to introduce how this lifetime information can be used for the system level reliability for the power electronics based power system taking the example of the microgrid application. New concept of system level reliability management based on lifetime model is envisaged.