This paper presents a study on the gate driver circuitries that need to be implemented to drive several power devices in series connection. More specifically, the propagation paths of parasitic currents through the gate driver circuitries, exited under high switching speeds, are studied in different configurations trying to minimize common mode currents generated. In a gate driver for a regular low side/high side configuration, the voltage transient dv/dt at the middle point applied across the primary-secondary parasitic capacitance of gate driver supplies and control signal isolation units are the reasons for the generation of conducted EMI perturbations. In complex power converters, multi-cell, multi-level or even series connection of power devices, there are several dv/dt generated at different floating points producing conducted EMI perturbations from the power part to the control part through many gate drivers. Based on previous works, this paper analyses the best configuration to minimize parasitic currents, especially reducing the conducted common mode currents in series connected transistors topologies. Simulations and practical results validate the analysis for two power devices in series connection, and then the extrapolations for more power devices in series connection, up to six are discussed and analyzed with the help of simulations results.
The proposed study is about the design and experimental results of a power supply for gate drivers that can sustain 40 kV of insulation voltage with a parasitic capacitance of 4 pF. The first section focuses on insulation materials suitable for medium voltage capabilities and therefore to justify the use of polyesterimide and Teflon polytetrafluoroethylene materials. In a second step, experimental results are provided to guaranty that with a thickness of 1 mm of the insulation material, an insulation voltage of 40 kV is provided. Then, a DC–DC converter based on a series‐series topology is designed and lead to a physical prototype of 5 W. The measured parasitic capacitance is 4 pF between the primary and the secondary sides.
Power Electronics Converters (PEC) play a crucial role in the operation of many modern electrical systems and devices. Despite their widespread use, the lack of an efficient and cost-effective disassembly process can limit their repairability, refurbishability, remanufacturability and, ultimately, recyclability, thus hindering the circularity of products. In order to improve their circularity, it is important to assess their ease of disassembly. Therefore, this paper investigates the applicability of the “ease of Disassembly Metric” (eDiM), which is referenced in the material efficiency standards, Benelux repairability assessment method, and Repair Scoring System (RSS), to analyze the ease of disassembly of energy-related products. After identifying the limitations of the eDiM method, we refined and adapted it to make it more suitable for Printed Circuit Board (PCB)-based PEC, and thus propose a PCB-based disassemblability assessment method allowing the implementation of quantifiable requirements supporting their circularity. This standardized approach, at the PCB level, can improve the circularity of such products by facilitating design enhancements. With this approach, policymakers and designers can contribute more effectively to the transition to a circular economy in PCB electronics, particularly in the field of power electronics.
11 September 2020 in IEEE Transactions on Power Electronics
This paper presents a cascaded gate driver power supply configuration to reduce the common mode (CM) current in phase-shifted full-bridge (PSFB) converters. In such converters, there are at least two dV=dt sources generated at different floating points associated to the parasitic capacitances of the isolated barriers of the gate drivers (power supplies and control signal isolation units), which can increase the conducted electromagnetic interference (EMI) perturbations. This paper is focused on the analysis of a new gate driver power supply configuration, which reduces the CM currents that circulate in the control part of the switching cells. This improvement is achieved by modifying the impedance network of CM current pathways. Experimental results are provided to prove the effectiveness of the new gate driver power supply configuration on a PSFB converter based on SiC-MOSFETs devices.
In this study, a design methodology for optimising a signal transmission function for high galvanic insulation (up to 30 kV) insulated gate bipolar transistor gate driver is proposed. The technology is based on a printed circuit board magnetic planar transformer with electronic circuits for excitation and reception. The objective of this study is to optimise the geometric elements of the transformer and its associated electronics devices with the help of a virtual prototyping tool. A bi‐objective problem of the overall system that leads to a Pareto front is presented. Several Pareto fronts’ results are obtained assuming different insulation layers thickness. The chosen transformer solution is justified and depends on the bi‐objective functions and the galvanic insulation level of the system. Moreover, the experimental results are compared with the simulation results. Finally, the comparisons between experimental and simulation results are proposed to lead to a conclusion of this methodology.