Since their introduction in 2017, the efficiency of lead‐free halide perovskite solar cells based on Cs2AgBiBr6 has not exceeded 3%. The limiting bottlenecks are attributed to a low electron diffusion length, self‐trapping events and poor selectivity of the contacts, leading to large non‐radiative VOC losses. Here, 2D/3D hybrid double perovskites are introduced for the first time, using phenethyl ammonium as the constituting cation. The resulting solar cells show an increased efficiency of up to 2.5% for the champion cells and 2.03% on average, marking an improvement by 10% compared to the 3D reference on mesoporous TiO2. The effect is mainly due to a VOC improvement by up to 70 mV on average, yielding a maximum VOC of 1.18 V using different concentrations of phenethylammonium bromide. While these are among the highest reported VOC values for Cs2AgBiBr6 solar cells, the effect is attributed to a change in recombination behavior within the full device and a better selectivity at the interface toward the hole transporting material (HTM). This explanation is supported by voltage‐dependent external quantum efficiency, as well as photoelectron spectroscopy, revealing a better energy level alignment and thus a better hole‐extraction and improved electron blocking at the HTM interface.
Finding lead‐free alternatives remains an important and challenging topic in the field of perovskite solar cells. In this perspective, the potential of Cs2AgBiBr6 double perovskites in solar cells is discussed based on reported absorption and emission data. Whereas the material is capable of exceeding and potentially doubling current efficiency values of around 3%, mainly by an optimized solar cell design, industrially relevant devices cannot be fabricated without major changes in the absorption onset. Nevertheless, Cs2AgBiBr6 poses various scientific questions and exact recombination and charge transport processes are yet to be unraveled, preparing us for the double perovskite or perovskite‐like materials to come.
11 November 2017 in Journal of Materials Chemistry A
The current state-of-the-art hole transporting materials (HTM) for perovskite solar cells are generally synthesized via cross-coupling reactions that require expensive catalysts, inert reaction conditions and extensive product purification, resulting in high costs and therefore limiting large-scale commercialisation. Here we describe a series of HTMs prepared via simple and clean Schiff-base condensation chemistry with an estimated material cost in the range of 4–54 $ per g. The optoelectronic and thermal properties of the materials are linked to the changes in the chemical structure of the HTMs, which allow us to extract design rules for new materials, supported by density functional theory calculations. Charge transport measurements show hole mobilities in the range of 10−5 to 10−7 cm2 V−1 s−1. Upon addition of LiTFSI the HTMs can be oxidized, resulting in a large increase in the conductivity of the hole transporting layer (HTL). When employed as HTL in perovskite solar cells, power conversion efficiencies close to those of spiro-OMeTAD are obtained. In particular, devices prepared with Diazo-OMeTPA show a higher open-circuit voltage. Furthermore, we show that azomethine-based HTMs can act as effective moisture barriers, resulting in a significant increase in the stability of the underlying perovskite film. We assign the improved properties to the presence of a dipole in our molecules which promotes a close molecular packing and thus leads to a high density of the as-formed HTM films, preventing the ingress of water. This work shows that HTMs prepared via condensation chemistry are not only a low-cost alternative to spiro-OMeTAD, but also act as a functional barrier against moisture-induced degradation in perovskite solar cells.
Cs2AgBiBr6 has attracted much interest as a potential lead‐free alternative for perovskite solar cells. Although this material offers encouraging optoelectronic features, severe bottlenecks limit the performance of the resulting solar cells to a power conversion efficiency of below 3%. Here, the performance‐limiting factors of this material are investigated in full solar cells featuring various architectures. It is found that the photovoltaic parameters of Cs2AgBiBr6‐based solar cells strongly depend on the scan speed of the J/V measurements, suggesting a strong impact of ionic conductivity in the material. Moreover, a sign change of the photocurrent for bias voltages above 0.9 V during the measurement of the external quantum efficiency (EQE) is revealed, which can be explained by non‐selective contacts. The radiative loss of the VOC from sensitive subgap‐EQE measurements is calculated and it is revealed that the loss is caused by a low external luminescence yield and therefore a high non‐radiative recombination, supported by the first report of a strongly red shifted electroluminescence signal between 800 and 1000 nm. Altogether, these results point to a poor selectivity of the contacts and charge transport layers, caused by poor energy level alignment that can be overcome by optimizing the architecture of the solar cell.
Two‐dimensional (2D) hybrid double perovskites are a promising emerging class of materials featuring superior intrinsic and extrinsic stability over their 3D parent structures, while enabling additional structural diversity and tunability. Here, we expand the Ag–Bi‐based double perovskite system, comparing structures obtained with the halides chloride, bromide, and iodide and the organic spacer cation 4‐fluorophenethylammonium (4FPEA) to form the n = 1 Ruddlesden–Popper (RP) phases (4FPEA)4AgBiX8 (X = Cl, Br, I). We demonstrate access to the iodide RP‐phase through a simple organic spacer, analyze the different properties as a result of halide substitution and incorporate the materials into photodetectors. Highly oriented thin films with very large domain sizes are fabricated and investigated with grazing incidence wide angle X‐ray scattering, revealing a strong dependence of morphology on substrate choice and synthesis parameters. First‐principles calculations confirm a direct band gap and show type Ib and IIb band alignment between organic and inorganic quantum wells. Optical characterization, temperature‐dependent photoluminescence, and optical‐pump terahertz‐probe spectroscopy give insights into the absorption and emissive behavior of the materials as well as their charge‐carrier dynamics. Overall, we further elucidate the possible reasons for the electronic and emissive properties of these intriguing materials, dominated by phonon‐coupled and defect‐mediated polaronic states.