K. David Huang

K. David Huang

Auto-generated profile, based on publicly available information

K. David Huang

Department of Vehicle Engineering, National Taipei University of Technology, Taipei, Taiwan

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2011 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
EDEnpeng Du
Enpeng Du
HTH. Tang
H. Tang
KHK. Huang
K. Huang
RTR. Tao
R. Tao
Improving engine efficiency and reducing pollutant emissions are extremely important. Here the authors report their finding, using electrorheology to reduce the viscosity of diesel fuel. Diesel is made of many different molecules, 75% small molecules and 25% large molecules. In addition, it contains other nanoscale particles, such as sulfur. Therefore, diesel can be regarded as a liquid suspension. Under a strong electric field, the large molecules aggregate into small clusters, yielding a lower viscosity. For high-sulfur diesel, the applied electric field is around 1 kV/mm. However, for ultra-low-sulfur diesel, the required electric field must be around 2 kV/mm. This viscosity reduction leads to finer mist in fuel atomization, improving the combustion, and engine efficiency.

14 June 2021 in Journal of the Chinese Institute of Engineers
Verified
Journal Article
Closed access
KNKhoa Nguyen
Khoa Nguyen
STSANGEETHA THANGAVEL
SANGEETHA THANGAVEL
PCPo-Tuan Chen
Po-Tuan Chen
THTing-Wei Hsu
Ting-Wei Hsu
WYWei-Mon Yan
Wei-Mon Yan
KHK. David Huang
K. David Huang
This research examined the operation of zinc–air fuel cell (ZAFC) with two different anode fuel types, namely zinc plate and zinc particle. The cell operation with zinc particle fuel also included potassium hydroxide (KOH) as the flowing electrolyte, and the optimal electrolyte flow rate was established as 150 mL/min. The performance of the two cells was compared in terms of power performance and reduction in reactor internal resistance. The power performance evaluation depends on three main factors including open-circuit voltage (OCV), power, and current density. The ZAFC with particle fuel was better than the plate-type fuel cell with maximum OCV of 1.41 V and current and power density values of 684 mA/cm2 and 553.6 mW/cm2, respectively. The particle fuel cell with flowing electrolyte also showed better reduction in external ohmic resistance, kinetic resistance, and mass-transport resistance with values of 0.41, 0.14, and 0.19 Ω, respectively, but a slight increase in internal resistance of the particle ZAFC (0.20 Ω) over plate anode fuel cell (0.18 Ω) was observed. Nyquist and Bode plots were used to explain the results in this study.

27 January 2021 in Journal of the Chinese Institute of Engineers
Verified
Journal Article
Closed access
KHK. David Huang
K. David Huang
Cheng-Jung YangCheng-Jung Yang
Cheng-Jung Yang
PCPo-Tuan Chen
Po-Tuan Chen
Zinc-air fuel cells (ZAFCs) have great potential as next-generation green energy sources. However, a practical application remains a challenge, because to achieve continuity and automation the operation of ZAFCs includes manipulation of the electrolyte and Zn fuel, for which the control of liquid–solid interface is difficult. Therefore, a fluid-circulation system has been developed for a ZAFC in this study. A flowing electrolyte is used to feed the Zn particles into the cell. Moreover, the operation parameters are adjusted to obtain the best cell performance, and a Ni-filter current collection grid (CCG) has been incorporated. The experimental results show that the optimal area for the Ni-filter CCG box is 300 cm2, and 0.15 mm Zn particles are optimal for facilitating cell efficiency. The flow rate requires appropriate control to allow Zn particles to complete their reaction. A flow rate of 65 mL/min was found to be optimal. After optimization of the parameters, a single cell can produce a maximum power of 19 W, under a continuous feed of 400 mA/cm2, with a corresponding peak current density of 500 mA/cm2. It is capable of continuous discharge for up to 300 min when the voltage is maintained above 0.8 V, thus verifying the potential and feasibility of the proposed design.