1 January 2021 in Vektor nauki Tol'yattinskogo gosudarstvennogo universiteta
PUPeter the Great St. Petersburg Polytechnic University
Peter the Great St. Petersburg Polytechnic University
Additive technologies are among the most rapidly developing areas of modern production. To ensure the progressive movement of additive technologies development in the Russian Federation, it is necessary to provide maximum availability of additive raw materials – spherical metal powders for the domestic enterprises; however, the absence of domestic assemblies to produce such powders hampers the solution of this issue. Peter the Great St. Petersburg Polytechnic University has developed and successfully carried out industrial tests of a plasma atomization system for solid metal feedstocks of various chemical compositions. The paper presents the results of the study of the influence of some technological parameters on the granulometric size, shape, and defect structure of 12H18N9 steel and VG98 alloy powders. The paper includes the results of the research of the influence of such spraying parameters as the current strength and the plasma-forming gas velocity supplied to the plasma generator and the volume of protective gas supplied to the spray torch through the fluidized bed system nozzles located in the midsection of the atomizer spraying chamber. The study showed that by increasing the current strength and the plasma-forming gas velocity, it is possible to reduce the average size of the powder particles; and by changing the volume of the protective gas supply, it is possible to control the particle shape. The analysis of the chemical composition of the obtained powders shows that during the spraying process, there is no loss of alloying elements and the powder composition is the same as the original feedstock compositions. The paper gives the developed modes for the alloy feedstocks spraying, shows the possibility to produce metal powders with the level of the spherical shape factor of 92–96 % and minimal – not exceeding 0.5 % of powder aggregate weight – number of particles with nonmetallic inclusions, external and internal defects.
5 September 2024 in Oil and Gas Studies
Relocation of the main capacities of oil production infrastructure from Central to Northern Russia necessitated a re-evaluation of oilfield development strategies, particularly addressing the challenges of constructing foundations for pipelines, processing facilities, and power plants. These foundations are formed by drill-dipping piles into pre-drilled boreholes. The use of drill dipping piles in permafrost is technologically essential as alternative pile types are impractical. The most common are drill dipping piles fabricated from longitudinal seam pipes welded with high frequency current techniques (as per GOST 20295 and GOST R 58064). Performance of such pipes in permafrost conditions was evaluated through laboratory simulations mimicking operational conditions, as well as in-situ at the test site of Federal Research Centre "The Yakut Scientific Centre of the Siberian Branch of the Russian Academy of Sciences" where full-size piles were installed in firm loamy and wet peaty permafrost soils. Pipes both with and without post-weld heat treatment, as specified in SP 16.13330.2017, were tested. The authors examined static mechanical properties and impact toughness of the base metal and welded joints of the pipes, as well as corrosion resistance and crack resistance. The research revealed that post-weld heat treatment did not significantly enhance the reliability of drill dipping piles fabricated from 09G2S steel. Concurrently, microstructure analysis of the welded joints revealed a considerable number of defects along the weld-fusion line, potentially accelerating pile failure.
25 December 2025 in Vestnik of Nosov Magnitogorsk State Technical University
The shift of the main extractive industries to the northern and northeastern regions of the country, and the in-tensification of industrial and housing construction in the Far North have posed several complex technological chal-lenges to adapt various types of basic and auxiliary equipment to the extreme climatic conditions of the Arctic and Subarctic regions. Such equipment includes ventilation and cooling systems for industrial premises, various stationery and mobile equipment. As the analysis of the actual operation of fans in conditions of low climatic temperatures and high humidity in the northern areas has shown, the use of traditional materials for their manufacture, for example, polymer composite materials based on polybutylene terephthalate matrix, is in some cases impossible due to their low cold and crack resistance, leading to the destruction of fan housings and impellers. The paper analyzes the possibility of using polymer composite materials to manufacture the main components of an axial fan, which is expected to operate in an Arctic climate. Mathematical modeling of fan operating conditions in the ANSYS software package and FMEA risk analysis is performed. Assessment of critical factors affecting the reliability and durability of fans made of various polymer composite materials and operated at extremely low temperatures. Data on degradation of the mechanical properties of polymer composite materials under conditions of prolonged exposure to low ambient temperatures and increased operating temperatures are provided. The rate of degradation of strength properties under the influence of thermal cyclic effects of temperature (ambient temperature zero crossing) and increased salinity of the air is determined. The possibility of manufacturing axial fan housing and impellers from glass-filled polymer composite materials with a polycarbonate matrix for use in extremely low temperature conditions is shown.
30 October 2026 in Oil and Gas Studies
The expanding use of polymer composites in infrastructure calls for recycling routes after the end of service. This study evaluates mechanically ground material from a hybrid basalt/glass-fibre composite pile as a filler for acrylonitrile butadiene styrene (ABS) filament and three-dimensional printing. Formulations containing 0, 10, 20 and 30 wt.% recyclate of a 0.10–0.20 mm sieve fraction were used to print two tensile and three three-point-bending specimens per formulation. The printing nozzle temperature was 260 °C. Mean maximum tensile stress decreased from 44.21 MPa for unfilled ABS to 35.49, 32.35 and 20.00 MPa, while flexural stress decreased from 79.58 to 70.46, 58.88 and 43.80 MPa, respectively. Flexural modulus remained within 2.60–2.77 GPa. At 30 wt.%, filament brittleness, winding difficulties and intermittent extrusion-nozzle clogging limited continuous filament length to 10 m. Formulations containing 10–20 wt.% recyclate warrant further development for auxiliary products whose intended use permits reduced mechanical performance. The results support further optimization of particle classification and processing conditions but do not establish a universally optimal formulation.