Didier Bouvard

Didier Bouvard

Auto-generated profile, based on publicly available information

Didier Bouvard

National Centre for Scientific Research (CNRS), Science et Ingénierie des Matériaux et Procédés (SIMAP), Grenoble Institute of Technology (Grenoble INP), Universite Grenoble Alpes, 38000 Grenoble, France

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2014 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
Zilin YanZilin Yan
Zilin Yan
CMC.L. Martin
C.L. Martin
OGO. Guillon
O. Guillon
DBD. Bouvard
D. Bouvard
CLC.S. Lee
C.S. Lee

30 December 2022 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
AVAatreya Manjulagiri Venkatesh
Aatreya Manjulagiri Venkatesh
DBDidier Bouvard
Didier Bouvard
PLPierre Lhuissier
Pierre Lhuissier
JVJulie Villanova
Julie Villanova

2 February 2023 in Advanced Engineering Materials
Verified
Journal Article
Closed access
JCJean-Marc Chaix
Jean-Marc Chaix
Renaud BouchetRenaud Bouchet
Renaud Bouchet
DBDidier Bouvard
Didier Bouvard
TFTimothée Fabre
Timothée Fabre
TGTristan Garnault
Tristan Garnault
MSMarlu Cesar Steil
Marlu Cesar Steil

19 October 2016 in Powder Metallurgy
Verified
Journal Article
Closed access
EBE. Biguereau
E. Biguereau
DBD. Bouvard
D. Bouvard
JCJ. M. Chaix
J. M. Chaix
SRS. Roure
S. Roure
Silver powder compacts may suffer an overall expansion during sintering. A simultaneous analysis of dimensional changes, mass loss and pore closing in the course of sintering showed that volume change results from the competition between classical sintering phenomena inducing densification and material creeping under stresses caused by internal gas pressure, which induces swelling. The internal gas includes air trapped during pressing and oxygen released from particle surface inside the pores that closed during pressing or sintering. This swelling phenomenon is particularly strong with powders with large specific surface area and compacts with high green density. It is less effective during fast sintering, as observed during direct induction heating experiments. Electrical conductivity is strongly affected by swelling. Powder compacts may exhibit a lower conductivity after sintering when interparticle bonding does not balance the density decrease occurring during sintering.

21 June 2019 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
JCJorge Chávez
Jorge Chávez
OJOmar Jiménez
Omar Jiménez
Martín FloresMartín Flores
Martín Flores
HVHector Javier Vergara-Hernandez
Hector Javier Vergara-Hernandez
LOLuis Olmos
Luis Olmos
DBDidier Bouvard
Didier Bouvard

4 May 2023 in Metals
Verified
Journal Article
Open access
PDF file
HVHector Javier Vergara-Hernandez
Hector Javier Vergara-Hernandez
LOLuis Olmos
Luis Olmos
VGVictor Solorio García
Victor Solorio García
DBDidier Bouvard
Didier Bouvard
JVJulio Villalobos
Julio Villalobos
OJOmar Jiménez
Omar Jiménez
Ti6Al4V (Ti64) alloy is the most used metal material for bone implants because of its good biocompatibility and adapted mechanical properties. Nevertheless, it shows low antibacterial activity, which may favor its failure. Addition of antibacterial elements such as copper should avoid this drawback. This work studies the addition of Cu into a Ti64 matrix resulting in Ti64/xCu composites. Powder mixtures of Ti64/xCu were compacted in a die and then sintered at 1100 °C. Sintering kinetics indicate that densification is achieved by pore filling due to eutectic liquid formed by the reaction of Ti and Cu. The microstructure of the sintered samples is composed mainly of α-Ti and Ti2Cu phases, but TixCuy intermetallics were also found. Microhardness is increased by the addition of Cu due to densification and the formation of harder phases such as Ti2Cu. However, the stiffness and compression strength are barely the same for all composites. The corrosion resistance is significantly improved by the addition of Cu. Finally, the material with 15 wt% of copper showed the best compromise.