The current differential protection is the most popular protection for transformers, providing good fault sensitivity, selectivity and security. Depending on the application, the transformer size, shape, winding connections vary. Some common power system applications require installation of two- or three-winding conventional power transformers or autotransformers, while others require phase shifting transformers (PST), Scott transformers, LeBlanc transformers, Zig-Zag grounding transformers, or converter transformers. Applying differential protection to conventional type power transformers with “standard” phase shifts of 30 degrees, or multiples of 30 degrees is trivial. However, applying this protection to transformers with non-standard phase shifts is challenging for the protection engineer. Current Transformers (CTs) installed in non-common locations adds even more to the complexity of applying the protection correctly. The later is associated with special CT - relay connections, correct computation of winding currents, phase angles, and selection of protective device supporting such applications. The paper provides essential knowledge on the transformer differential protections throughout theory and application examples. Current transformers and relay connections, as well as computation of transformer setup settings with standard and non-standard phase shift are covered.
In order to identify dangerous behaviors such as fighting in public area, proposed a deep learning model that combines human post estimation and action analysis for behavior recognition. The model takes video frame sequence as input, first make use of HRNet as backbone network to detect human body joints and generate human pose frame sequence, and then, make use of recurrent neural network for action analysis from the pose frame sequence, thus determine whether there is dangerous behavior in this video. In the first part, optimization was made on HRNet so as to reduce its parameter and improve the accuracy of joint location. In the second part, introduced Cubic LSTM as a comprehensive model for action recognition, which analysis the motion of human joints from both temporal sequence and spatial sequence, thus achieve better inference score. Experiments show that the recognition accuracy of the proposed method can reach 92.8%. In the last part, a dangerous behavior recognition system is developed based on this model, which use a monitoring host to analysis the captured video frames from cameras, and identify dangerous behavior from them automatically, thus serve for public security tasks.
Dynamic line rating current is widely used in the smart grid for improving the efficiency and economy of the power transmission and distribution. The rating current is determined by the ambient parameters such as convection heat loss rate, solar radiation, wind power, wind direction, etc. This paper proposes a method for calculating dynamic rating current only by means of the measurement of voltage and current of the two ends of the line free from any ambient parameter inputs. The instantaneous temperature can be estimated by calculating the variation of the line parameters, and subsequently the steady state conductor temperature can be obtained. The rating current is calculated by curve fitting of the dissipating power curve based on the steady state conductor temperature obtained and the conductor current. The scientific model of this technique, which is implementable into products, is constructed using Matlab/Simulink. Simulation tests show that the calculated dynamic line rating current is reliable and accurate.
The mainstream segmentation methods may suffer from problems in the separation of boundaries due to the presence of adhesion and overlapping. Therefore, subsequent processing is further required for segmentation tasks in different applications to obtain better performance. This paper proposes a post- segmentation processing method to solve the problem of boundary adhesion and overlapping. The method relies on morphological characteristics, which uses graphical rules to detect the target contour, find the adhesion area, and make judgments for separation. The proposed method is verified on post-segmentation processing of prediction masks of ore images, in which an improved U-Net model is firstly applied for ore image segmentation and then the proposed method is further applied for better boundary separation. The improved U-Net model segments the ores in pixel-level according to their types and output prediction masks of ore images. However, there are adhesions and overlaps among ores in the prediction masks. And our work strives to separate the adhered ore in the prediction masks. The experimental results show that our method is efficient in boundary separation.
As a simplified MMG (Manoeuvring Model Group) model, the ship motion model proposed in the standard of the International Electrotechnical Commission (IEC62065) has limitation of imprecise motion simulation for atypical ship, because of the simplification of some physical quantity such as propeller thrust and fluid resistance. To keep the concision of the IEC62065 model and address the issues of inaccuracy of atypical ship, this paper proposed a method of simplifying the complex MMG model with considerable accuracy for atypical ship into IEC62065 model. By designing motion simulation experiment of the complex MMG model for atypical ship, the relevant parameters in the IEC62065 model for the atypical ship will be calculated. Comparing the simulation results of the IEC62065 model with complex MMG model for the same atypical ship, it shows a high fitting degree between them. By using the method, a good model simplification effect can be obtained.