23 March 2005 in Machining Science and Technology
Procedures and results of experimental work to measure residual stresses and hardness depth in electric discharge machined surfaces are presented. Layer removal method is used to express the residual stress profile as a function of depth caused by a die sinking type EDM. Thin stressed layers are removed from machined samples by electrochemical machining. Corresponding deformations due to stress relaxation are recorded for each removal to determine the stress profile from elasticity theory. The relational dependence of the machining parameters with residual stresses is obtained and a semi-empirical model is proposed for plastic mold steel for de-ionized water as dielectric liquid. These stresses are found to be increasing rapidly with respect to depth, attaining to its maximum value, around the yield strength, and then fall rapidly to compressive residual stresses in the core of the material since the stresses within plastically deformed layers are equilibrated with elastic stresses.
1 February 2005 in Metallurgical and Materials Transactions B
1 March 2008 in Surface and Coatings Technology
30 June 2008 in Engineering Failure Analysis
24 January 2012 in Advanced Materials Research
Hydroxyapatite (HA) is the major component of the natural hard tissues such as teeth and bone. It has been studied extensively as a candidate biomaterial for its use in prosthetic applications. However, the main weakness of this material lies in its poor mechanical strength which makes it unsuitable for load-bearing applications. On the other hand zirconia (ZrO2) powder has been widely studied because of its high strength and fracture toughness and good biocompatibility. Therefore, the addition of zirconia phase into HA will improve the mechanical properties and biocompatibility of HA ceramics. The present study focused on coating of HA-ZrO2 on commercially pure titanium (cp-Ti) using novel biomimetic sol-gel method. The HA-ZrO2 coatings produced with BSG method were exhibited highly crystalline and pure structure. The coating thickness of the samples was not significantly influenced by the change in gelatin concentration and volume. It was concluded that the suggested coating method is a useful method to produce a biomimetic coating layer on the cp-Ti sample surfaces.
24 January 2012 in Advanced Materials Research
Titanium (Ti) and Ti-alloys are often used in dental and orthopedic applications because of their good mechanical properties and biocompatibility. The advantages of Ti and Ti-alloys are its superior corrosion resistance, high fatigue strength and low elastic modulus which reduce stress shielding. Morover biocompatibility of them can be improved coating with bioceramics such as hydroxyapatite (HA) or other ceramic composites. The hydroxyapatite [Ca10(PO4)6(OH)2, H is frequently used as a coating material on the surfaces of Ti-based medical implants to improve the bone fixation and thus the lifetime of the implant is increased. However, the main weakness of HA lies on its poor mechanical strength that makes it unsuitable for load-bearing applications. An attractive way to produce the tougher HA is to use composite powders such as Yttria-Doped Zirconia-Hydroxyapatite (YSZ-HA) consisting of 8 mol% yttria-stabilized tetragonal zirconia (YSZ) so that the apatite phase increases the biocompatibility and zirconia (ZrO2) phase improves the strength. Y2O3 addition into zirconia can stabilize the tetragonal phase at room temperature (YSZ) and the tetragonal phase plays a major role to increase the fracture toughness. In the present study yttria-dopped zirconia powders by using ZrO(NO3)2.xH2O and Y(NO3)3.6H2O were produced to synthesize HA-YSZ composites. In accordance with this purpose, at the first step, Ca (NO3)2.4H2O, (NH4)2HPO4 and YSZ powders were dissolved in simulated body fluids (SBF) to obtain sol. The gelatin solutions with different concentration were added into sol to provide the gelation. Then the surfaces of Ti implants were soaked in this solution. The coating rate of Ti samples was arranged as 14 cm/s and coated implants were sintered at 900°C. Structural analysis of coated powders was obtained by using XRD. Morphological examinations and coating thickness were investigated by SEM. After the sol-gel solution was dried at 80°C, dried-powder was sintered at 900°C. Sintered powders were analyzed by FT-IR to determine any gelatin residue.