14 March 2023 in IEEE Transactions on Plasma Science
Launch efficiency has always been the focus of reluctance coil launchers research. In a traditional launch mode, the residual current in the drive coil creates a reverse force on the projectile. This is undesirable since the reverse force is in the opposite direction of movement, reducing the launch efficiency of the system. To address this problem, a multistage discharge circuit with the residual energy recovery and utilization mode is proposed in this article. As the projectile approaches the center of each stage of the drive coil, the current in the drive coil decays rapidly to zero by using the last stage capacitor to absorb the residual energy. The residual energy from the previous stages is eventually recovered by the last stage capacitor. This capacitor with residual energy is used to power the last stage drive coil of the reluctance coil launcher. This mode effectively suppresses the reverse force on the projectile and realizes the reuse of residual energy. Taking a four-stage reluctance coil launcher as an example, this article introduces the working principle of this mode in detail. The feasibility of the model is verified by finite-element simulation and experiments. Both simulation and experimental results show that this mode performs well in the recovery and reuse of residual energy and can effectively improve the launch efficiency of system.
21 April 2023 in IEEE Transactions on Plasma Science
The reluctance electromagnetic launchers mainly use the driving coils to generate high magnetic field to accelerate the ferromagnetic projectiles. Its advantages in accelerating large-mass projectiles have attracted considerable attention. However, during the projectile acceleration of conventional reluctance electromagnetic launchers, residual currents in the drive coils may produce opposing forces that reduce launch speed and efficiency. For this issue, an improved pulsed power supply circuit for reluctance electromagnetic launchers is proposed in this article based on a bridge-type capacitor circuit. The circuit can quickly reduce the residual current of the driving coil and recover the residual current energy. Since the circuit uses the same capacitor to power the drive coil and recover the remaining energy, the remaining energy recovered by the capacitor can be used as the initial energy storage for a new cycle. This can shorten the charging time for new cycles. In this article, the basic principle of the improved pulsed power supply circuit is introduced and analyzed in detail, and a comparative analysis is carried out with the traditional circuit through simulation. The results show that the new circuit has better characteristics in terms of residual energy recovery.
27 June 2023 in IEEE Transactions on Plasma Science
Launch efficiency is an important indicator to judge the performance of electromagnetic launchers. The goal of the conventional parameter optimization method for multistage launch is to maximize projectile kinetic energy in each stage acceleration. For reluctance coil launchers with residual recovery and utilization mode, the effect of the launcher parameters on the recovery energy should be considered in addition to the kinetic energy of the projectile. In this article, the feasibility of the model and the correctness of the original model are first verified by a four-stage launching experiment. Then, the influence of the drive coil parameters on the projectile acceleration and energy recovery is analyzed through theoretical analysis. In addition, a drive coil parameter optimization method for multistage reluctance coil launchers with residual energy recovery and utilization mode is proposed. By this method, the coil parameters of the original simulation model are optimized, and the simulation and experimental results before and after optimization are compared. The comparison results show that the optimization method proposed in this article integrates the relationship between projectile velocity and recovery energy, which can significantly improve the overall launch efficiency of the multistage system.
4 December 2023 in IEEE Transactions on Plasma Science
The reluctance coil launchers have attracted the attention of researchers due to its advantages of no mechanical contact and easy implementation. One of the inherent obstacles of traditional reluctance coil launchers is that the electromagnetic force on the projectile is reversed during the launch process due to the influence of residual current in the driving coils. This affects the improvement of launch speed and efficiency. The method of suppressing this reverse electromagnetic force is to eliminate residual current in the driving coil. A bridge capacitor circuit was proposed in our previous studies. This circuit uses two insulated-gate bipolar transistors (IGBTs) to control the discharge of the capacitor to the driving coil and switch the residual current path to suppress the reverse electromagnetic force. For higher power reluctance coil launch systems, the cost of IGBT switches with high voltage and high current is expensive. In this article, a capacitive pulsed power supply circuit for reluctance coil launchers is presented. Unlike the above bridge circuit, thyristors are used as the main switch and the technique of inverse current commutation with semiconductor devices (ICCOSs) proposed by the Institute of Saint Louis (ISL) is used to turn off the residual current in the driving coil. The principle of the proposed circuit is described in detail, and its feasibility is verified by simulation comparison and experiment. The results show that the proposed circuit has promising application prospects in reluctance coil launchers.
31 January 2024 in IEEE Transactions on Plasma Science
Inductive pulsed power supplies (IPPSs) are considered an attractive alternative to capacitive supplies for electromagnetic launch (EML) in all-electric mobile systems. The main obstacle to the early development of IPPS is the switching technology of large current, which can now be solved by a technique called inverse current commutation with semiconductor devices (ICCOS). In this article, a novel repetitive IPPS circuit with an improved ICCOS module is proposed. A bridge-type circuit composed of a capacitor, a diode, a small inductor, and three thyristors is used as the ICCOS module. With the ICCOS module, the proposed circuit can turn off the main switch thyristor, recover the residual energy of the system, self-recover the capacitor voltage of the ICCOS module, and generate continuous current pulses. To verify the feasibility of the proposed circuit, simulations and experiments are carried out based on a small high-temperature superconducting (HTS) pulse transformer. The results confirm the theoretical analysis and show the validity of the circuit scheme.
18 September 2024 in IEEE Transactions on Applied Superconductivity
High-temperature superconducting (HTS) inductors have the advantages of low loss, low charging power, and long-term energy storage, making them very suitable for high-power inductive pulse power supplies (IPPS) for continuous electromagnetic launch (EML). However, driving the rail type EML requires high amplitude and a certain pulse width of the current pulse. The current inductive pulse power supply modes are difficult to meet this requirement. For this issue, this paper proposes a new multi-module IPPS circuit based on high-temperature superconducting pulse power transformers (HTSPPT). The proposed pulse power supply consists of three groups of HTSPPTs, each group consisting of 12 HTSPPTs forming a circular structure. By delaying parallel discharge of three sets of HTSPPT modules, high amplitude and wide pulse width current pulses can be generated. The feasibility of this power supply mode was preliminarily verified through simulation in the paper.