Catalysts have been synthesized using the Anderson polyoxometalates (POMs) (NH4)4[Ni(OH)6Mo6O18] (NiMo6POM), (NH4)6[Co2Mo10O38H4] · 7H2O (Co2Mo10POM), and H6[Co2Mo10O38H4] (Co2Mo10HPA) as the precursors and hydrogen peroxide as the solvent. The catalysts have been characterized by low-temperature nitrogen adsorption, XPS, and HRTEM. Their catalytic properties have been tested in thiophene hydrodesulfurization and in the hydrodesulfurization and hydrogenation of components of diesel oil. The active phase of the catalysts synthesized using the POMs is the type II CoMoS phase in which the mean plate length is 3.6–3.9 nm and the mean number of MoS2 plate per plate packet is 1.8–2.0. Use of hydrogen peroxide provides an efficient means to reduce the proportion of Co2+ promoter atoms surrounded by oxygen in the case of an impregnating solution containing both an ammonium salt of a heteropoly acid and a Co2+ salt. In the catalysts synthesized using cobalt salts of Co2Mo10HPA, the support surface contains the multilayer type II CoMoS phase and cobalt sulfides. These catalyst show high catalytic properties in thiophene hydrogenolysis and diesel oil hydrorefining. Models are suggested for the catalysts synthesized using Anderson POMs.
Co(Ni)MoS/Al2O3 catalysts have been prepared from ammonium 10-dodecamolybdodicobaltate (NH4)6[Co2Mo10O38H4] (further, Co2Mo10HPC) and cobalt(nickel) salts of 10-dodecamolybdodicobaltic acid H6[Co2Mo10O38H4] (hereinafter, Co2Mo10HPA). It has been found that a high activity of the Co(Ni)3-Co2Mo10HPA/Al2O3 catalysts in the hydrodesulfurization and hydrogenation reactions is due to the formation of a nanostructured type II CoMoS phase via the contact of the metals (Mo and Co(Ni)) at the molecular level. The use of Ni as a copromoter in the Ni3-Co2Mo10HPA/Al2O3 catalyst leads to a simultaneous increase, compared with Co3-Co2Mo10HPA/Al2O3, in the linear size of nanoparticles and the number of MoS2 layers in the packing of active phase. The nature of the promoter X has a substantial effect on the properties of X3Co2Mo10HPC/Al2O3 catalysts. It has been found that the catalysts with X = Co exhibit the highest activity in the hydrodesulfurization reactions and those with X = Ni, in hydrogenation reactions.
The catalytic properties of CoMoS/AlO and K–CoMoS/AlO laboratory catalysts versus those of the commercial catalyst NK-100 (CoMo/AlO) have been investigated in the hydrotreating of the heavy fraction of cat-cracked gasoline (CCG). The basic kinetic parameters of the hydrodesulfurization and olefin hydrogenation processes have been experimentally determined. The addition of 7.5 wt % potassium to the CoMoS/AlO catalyst decreases both the apparent activation energy and preexponential factor of both processes and increases the selectivity coefficient by a factor of over 3. Selective hydrotreating of the heavy fraction of CCG has been carried out over a K–CoMoS/AlO sample at a temperature of 280°C, a pressure of 1.5MPa, a feed hourly space velocity of 7.5 h, and H: feed = 100 NL/L. As a result, the sulfur content of gasoline has been reduced from 92 to 13 mg/kg without affecting the octane number. If the proportion of CCG in commercial gasoline obtained by compounding CCG with other components is 20–35%, the sulfur content of the product will meet the environmental requirements imposed on Class 5 fuels according to regulations.
Petroleum sulfonates with the active substance content from 21 to 32.5 % wt were prepared from four extracts of solvent refining by phenol and N-methylpyrrolidone (oil side streams II and III) in laboratory conditions. Their average molecular weight, composition, and surface activity were evaluated using a rotating drop test. The sulfonated products were characterized by NMR, IR spectroscopy, and HPLC methods.
16 November 2016 in Petroleum Science and Technology
In the article we discuss the results of a comparison of interfacial activity and component composition data for petroleum sulfonates (PS) synthesized from an extract of selective N-MP refining of side stream II and for dimeric PS prepared from the same source in the presence of paraform (paraformaldehyde)—a component responsible for the formation of disulfonic acids. The prepared technical anionic PS are characterized by a higher molecular mass (688 g/mol) and lower CMC values (40-fold for the mass 120 concentration and 500-fold for the molar concentration) relative to paraform-free sulfonation of hydrocarbons. Surfactants with low CMC values sourced from the low-quality multitonnage hydrocarbon feedstock are promising in a search of formulations for chemical flooding of reservoirs.