John Papapolymerou

John Papapolymerou

Auto-generated profile, based on publicly available information

John Papapolymerou

Department of Electrical and Computer Engineering, Michigan State University, East Lansing, MI, USA

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 September 2016 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Open access
FCFan Cai
Fan Cai
YCYung-Hang Chang
Yung-Hang Chang
KWKan Wang
Kan Wang
CZChuck Zhang
Chuck Zhang
BWBen Wang
Ben Wang
JPJohn Papapolymerou
John Papapolymerou
This paper presents low-loss 3-D transmission lines and vertical interconnects fabricated by aerosol jet printing (AJP) which is an additive manufacturing technology. AJP stacks up multiple layers with minimum feature size as small as 20 $\mu \text{m}$ in the $xy$ -direction and 0.7 $\mu \text{m}$ in the z-direction. It also solves the problem of fabricating vias to realize the vertical transition by 3-D printing. The loss of the stripline is measured to be 0.53 dB/mm at 40 GHz. The vertical transition achieves a broadband bandwidth from 0.1 to 40 GHz. The results of this paper demonstrate the feasibility of utilizing 3-D printing for low-cost multilayer system-on-package RF/millimeter-wave front-ends.

14 May 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
MCMichael Thomas Craton
Michael Thomas Craton
XKXenofon Konstantinou
Xenofon Konstantinou
JAJohn D. Albrecht
John D. Albrecht
PCPremjeet Chahal
Premjeet Chahal
JPJohn Papapolymerou
John Papapolymerou
We show in this article two fully additively manufactured microwave packages with integrated active and passive components. Packages were constructed using a chip-first approach where package substrates (dielectrics) and interconnects (conductors) are built up around power amplifier bare die attached to carriers. Bypass capacitor dielectrics were printed using multimaterial aerosol jet printing, where aerosols of barium titanate and polyimide inks are mixed in place to fabricate a high dielectric constant polymer matrix nanocomposite film. The material properties of the film are characterized using three printed capacitors. We present S-parameter measurements to characterize small-signal performance, as well as load-pull measurements at the saturated output power. Finally, we demonstrate package performance after power cycling and temperature cycling to show the effect of aging on the part and the robustness of this packaging strategy. We measured a maximum packaged gain of 21.7 dB and a saturated output power of 21.9 dBm for a commercial-off-the-shelf (COTS) medium power amplifier specified to have a gain of 22 dB and a saturated output power of 22 dBm. The printed package-level performance is compared with the published bare die performance and a measured COTS packaged amplifier.

24 September 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
MAMarvin Abt
Marvin Abt
ARAljoscha Roch
Aljoscha Roch
JQJubaid A. Qayyum
Jubaid A. Qayyum
SPSvenja Pestotnik
Svenja Pestotnik
LSLukas Stepien
Lukas Stepien
TSThomas Schuelke
Thomas Schuelke
We studied aerosol jet printing on flexible substrates for wearable and flexible electronic devices. First, we investigated the electrical conductivity of aerosol jet printed silver layers at different temperatures. An electrical conductivity up to 60% of bulk Ag was measured after sintering at 140 °C on a hot plate. Higher conductivities became possible with higher sinter temperatures. The printed ink showed a surprisingly high flexibility. Transmission lines were printed on flexible substrates [Kapton and Rogers liquid crystal polymer (LCP) foils], and the performance was measured up to 110 GHz. The coplanar waveguide transmission lines demonstrated insertion losses of 0.366 dB/mm for LCP and 0.546 dB/mm for Kapton foils at 110 GHz.

27 April 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
SVStavros Vakalis
Stavros Vakalis
LGLiang Gong
Liang Gong
YHYuxiao He
Yuxiao He
JPJohn Papapolymerou
John Papapolymerou
JNJeffrey A. Nanzer
Jeffrey A. Nanzer

20 February 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
JSJakub Sorocki
Jakub Sorocki
IPIlona Piekarz
Ilona Piekarz
KWKrzysztof Wincza
Krzysztof Wincza
SGSlawomir Gruszczynski
Slawomir Gruszczynski
JPJohn Papapolymerou
John Papapolymerou
In this article, a novel microwave microfluidic coupled-line sensor allowing for monitoring of proportional quantities and determination of complex permittivity of liquid dielectric samples through simple analytical formulas is proposed. The application of broadside coupling configuration enabled the sample to be placed in-between coupled strips, thus a high sensitivity can be obtained as the electric field for differential excitation is confined within the sample's volume. Moreover, the use of 3-D printing technology allowed for the realization of an insert with the microfluidic channel and dedicated liquid inlet/outlet. The sensitivity analysis of such a sensor is provided along with the system calibration technique, which is straightforward because of a fixed and well-defined geometry of the sensor-sample setup. An exemplary, general-purpose sensor along with a cal-kit was realized in a stripline structure and manufactured using a combination of laminate and PolyJet 3-D printing technologies. The broadband measurement results are provided for a water-ethanol solution with variable solvent content up to 12 GHz and for various alcohols featuring frequency-dependent complex permittivity up to 5 GHz. The sensor's performance is assessed and discussed.

7 August 2019 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Open access
COChristopher Oakley
Christopher Oakley
JAJohn D. Albrecht
John D. Albrecht
JPJohn Papapolymerou
John Papapolymerou
PCPremjeet Chahal
Premjeet Chahal
This paper presents a hybrid process to fabricate chip-to-board interconnects for microwave and millimeter-wave applications. It is a four step process: 1) cavities are etched in a copper backed organic substrate (Liquid Crystal Polymer, LCP), 2) Active and passive devices are mounted in the cavity using a soldering or adhesive material, 3) Spacing between the chip and the cavity edge is filled using a UV curable epoxy, 4) interconnects are formed between the chip pad and the substrate using aerosol jet printed silver ink. Cavities in the LCP substrate are etched using a wet process which is simple to implement and allows parallel processing of multiple cavities. Aerosol printing allows custom patterning of interconnects to achieve good impedance transition between the chip and the transmission lines on the LCP substrate. The filler material and associated structures are first characterized up to 40 GHz. A 0 dB attenuator is utilized to characterize the interconnect process followed by the demonstration of an embedded amplifier using fully printed transmission lines, RF interconnects and DC biasing. In addition, aerosol printing is utilized for rework of damaged interconnects. The proposed embedded active process demonstrated is simple to implement and low-cost, and provides an approach to design wide-band interconnects. Existing shortcoming of the embedded process is the metal contact to the semiconductor substrate at the edge leading to the formation of a Ag/GaAs Schottky contact, which can be eliminated by depositing a thin dielectric film on the exposed semiconductor region.