20 February 2020 in IEEE Transactions on Microwave Theory and Techniques
In this article, a novel microwave microfluidic coupled-line sensor allowing for monitoring of proportional quantities and determination of complex permittivity of liquid dielectric samples through simple analytical formulas is proposed. The application of broadside coupling configuration enabled the sample to be placed in-between coupled strips, thus a high sensitivity can be obtained as the electric field for differential excitation is confined within the sample's volume. Moreover, the use of 3-D printing technology allowed for the realization of an insert with the microfluidic channel and dedicated liquid inlet/outlet. The sensitivity analysis of such a sensor is provided along with the system calibration technique, which is straightforward because of a fixed and well-defined geometry of the sensor-sample setup. An exemplary, general-purpose sensor along with a cal-kit was realized in a stripline structure and manufactured using a combination of laminate and PolyJet 3-D printing technologies. The broadband measurement results are provided for a water-ethanol solution with variable solvent content up to 12 GHz and for various alcohols featuring frequency-dependent complex permittivity up to 5 GHz. The sensor's performance is assessed and discussed.
25 February 2021 in IEEE Transactions on Microwave Theory and Techniques
A novel robust approach for permittivity measurements of liquid materials in a wide frequency range is proposed. A high-sensitivity microwave-fluidic sensor is developed enabling direct determination of liquid samples' permittivity from the measured sensor's propagation constant. Importantly, neither sensor calibration using liquid standards nor sensor's geometry (except length) information is required, which is very advantageous for industrial applications. This is achieved through the sensor's geometry, which is a two-wire transmission line (TWL) encapsulated in a 3-D printed container, and thus, the liquid-under-test fully encloses the propagating electromagnetic waves. The measurement setup comprises the sensor cascaded between two microstrip-to-TWL transitions for which a simplified de-embedding procedure is proposed using only a THRU standard. For demonstration, a setup was developed with transitions operating within 1-10 GHz and tested up to 18 GHz by measurement of a set of alcohols to produce useful data within the transition bandwidth, which can be extended at the cost of increased uncertainty by postprocessing. Finally, the measurement error study has shown that a relatively low uncertainty and error with respect to the reference is obtained, verifying the usability of the developed measurement technique.
25 December 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
18 July 2018 in IEEE Sensors Journal
A novel method for the measurement of complex permittivity of liquid dielectric materials in a wide frequency range is proposed. The technique utilizes an open-ended two-wire transmission line sensor that is submerged in a liquid-under-test to determine its complex permittivity from the measured differential reflection coefficient. The proposed approach has been theoretically analyzed to derive the appropriate sensor’s model and the required calibration procedure as well as experimentally validated by measurements of three liquids having frequency-dependent complex permittivity. Moreover, measurement accuracy analysis has been provided, including the method‘s uncertainty estimation and error sources’ discussion. Finally, the measured permittivity of each liquid has been compared against tabularized data. Good agreement has been obtained proving the validity and applicability of the proposed method.
23 February 2021 in IEEE Access
An ultra-broadband multisection directional coupler designed in Monolithic Microwave Integrated Circuit (MMIC) technology has been presented. It has been shown for the first time that it is possible to achieve bandwidths exceeding one frequency decade, simultaneously taking under account technological constrains. The proposed directional coupler is composed of three coupled-line sections having different values of electrical lengths and coupling coefficients. The strongest coupled section has been designed as an asymmetric three-strip coupled-line section, whereas the rest of the sections have been implemented as symmetric two-strip coupled-line structures. To improve electrical performance of the coupler, a compensation method has been implemented together with loss analysis which has to be considered in lossy inhomogeneous medium. The proposed 3-dB directional coupler has been designed in PH25 process based on gallium arsenide (GaAs) from United Monolithic Semiconductors (UMS), and fabricated. The measurement confirms applicability of the design method in monolithic technology for such networks operating in bandwidth exceeding one frequency decade.
8 January 2013 in IEEE Antennas and Wireless Propagation Letters
A novel approach to the design of series-fed antenna arrays has been presented, in which a modified three-way slot power divider is applied. In the proposed coupler, the power division is adjusted by changing the slot inclination with respect to the transmission line, whereas coupled transmission lines are perpendicular. The proposed modification reduces electrical length of the feeding line to $1 \lambda$, hence results in dissipation losses' reduction. The theoretical analysis and measurement results of the 2 $\, \times \,$8 microstrip antenna array operating within 10.5-GHz frequency range are shown in the letter, proving the novel inclined-slot power divider's capability to provide appropriate power distribution and its potential application in the large antenna arrays.