Eneko Ortega

Eneko Ortega

Auto-generated profile, based on publicly available information

Eneko Ortega

Technological Institute of Microelectronics, University of the Basque Country (UPV/EHU), 48013 Bilbao, Spain

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2019 in Solar Energy
Verified
Journal Article
Open access
EOEneko Ortega
Eneko Ortega
GAGerardo Aranguren
Gerardo Aranguren
JJJuan Carlos Jimeno
Juan Carlos Jimeno

1 June 2017
Verified
Conference Paper
Closed access
EOE. Ortega
E. Ortega
GAGerardo Aranguren
Gerardo Aranguren
MSM.J. Saenz
M.J. Saenz
RGR. Gutierrez
R. Gutierrez
JJJ.C. Jimeno
J.C. Jimeno
To maximize photovoltaic systems performance the monitoring of them is essential. There are several faults that produce energy losses in the system. When a fault happens the monitoring system has to detect it and give an indication about which is the component with the fault. For this, in most system a set of parameters are measured, usually four: current, voltage, temperature and irradiance. In some monitoring systems these measures are obtained for the whole plant whereas in others, the modules are measured one by one. In this work, a study of these methods is presented.

1 June 2018
Verified
Conference Paper
Closed access
EOE. Ortega
E. Ortega
GAGerardo Aranguren
Gerardo Aranguren
MSM.J. Saenz
M.J. Saenz
RGR. Gutierrez
R. Gutierrez
JJJ.C. Jimeno
J.C. Jimeno
A PV plant monitoring system, which is able to detect faults in individual modules is presented. The system is divided in two parts: A control unit for the whole PV plant and a measuring circuit connected in parallel to each PV module. The measuring circuit is able to disturb the working point of the module and measuring this perturbation estimate the I-V characteristic of the module without disconnecting it from the rest of the system. The system is able to detect a fault in each module by obtaining the real outpout power, the expected power without failures, and the maximum power point. The system was designed in terms of low cost and simplicity, to operate in an automatic and remote way.

21 November 2016
Verified
Conference Paper
Closed access
EOE. Ortega
E. Ortega
GAGerardo Aranguren
Gerardo Aranguren
MSM.J. Saenz
M.J. Saenz
Roberto GutiérrezRoberto Gutiérrez
Roberto Gutiérrez
JJJ.C. Jimeno
J.C. Jimeno
A wireless system for photovoltaic plant monitoring is presented. The system detects faults in each individual photovoltaic module connecting several electronic circuits in parallel to each module and connecting them with a Wireless Sensor Network to a central wireless control unit. The general system and a first prototype of the electronic circuit for a single photovoltaic module are presented. The system was designed in terms of easy implementation and low cost, without any extra sensors.

1 June 2019
Verified
Conference Paper
Closed access
EOE. Ortega
E. Ortega
GAGerardo Aranguren
Gerardo Aranguren
JJJ.C. Jimeno
J.C. Jimeno
A Module to Module Monitoring System (M3S), which is able to determine Maximum Power Point of PV modules based on partial measures of I-V curves, is presented. M3S measures individual modules without power electronics and without disconnecting the PV module from the rest of the system. For that, the measuring circuit disturbs the operating point of the PV module during less than 5 ms, moving it to short-circuit and to open-circuit. From there it estimates the I-V characteristic of the PV module and computes the maximum power point of the module. Through a graphic interface the monitoring process is done automatically, without affecting PV system normal operation.

4 September 2026 in SiliconPV Conference Proceedings
Verified
Journal Article
Open access
PDF file
ÁBÁlvaro Briones-Garrachón
Álvaro Briones-Garrachón
MCMario Cruz-Giménez
Mario Cruz-Giménez
AOAloña Otaegi
Aloña Otaegi
VFVanesa Fano
Vanesa Fano
ECEneko Cereceda
Eneko Cereceda
JJJuan Carlos Jimeno
Juan Carlos Jimeno
Reducing the thickness of crystalline silicon solar cells is a crucial strategy for decreasing manufacturing costs and increasing mechanical flexibility. However, thinning the substrate fundamentally alters the optical and electrical behavior of the device. This study presents the analysis of the inherent trade-offs between optical absorption and internal carrier recombination in ultra-thin p-type silicon solar cells. To physically demonstrate these optical changes, standard n-type c-Si wafers were progressively thinned down by alkaline chemical etching achieving ultra-thin substrates of 70 μm, 50 μm, and 26 μm. A visual, rapid-assessment procedure utilizing a broad-spectrum white light source confirmed the filtering effect, demonstrating high transparency to red wavelengths at ultra-thinness. Reducing the cell thickness from the 150 μm to a 70 μm the effective absorption is limit to 955 nm. This leads to a loss in the absorption of higher-energy infrared photons, directly causing a drop in Jsc. Conversely, simulations reveal that this reduction in bulk silicon volume significantly decreases internal carrier recombination thereby driving an increase in Voc. The key challenge now lies in adapting industrial manufacturing equipment to realistically enable the large‑scale production of ultra-thin and flexible solar cells with low breakage rates.