25 June 2020 in IEEE Antennas and Wireless Propagation Letters
A compact monopulse antenna operating at 10 GHz is presented. The feed network consists of four rat-race couplers which generate sum and difference patterns in orthogonal radiation planes (azimuth and elevation). The focus was on improving performance by improving the matching circuit to generate in-phase and out-phase excitations while also maintaining a very high null-depth, which is applicable for tracking purposes. The electromagnetic energy is transmitted from the feed network to the radiators through via-coupling structure. Using the symmetrical via-fed patch array results in low mutual coupling between the antenna ports. A prototype of the proposed antenna was manufactured on a printed circuit board and tested. A suitable agreement between the measurement and simulation results was obtained. The results show a -10-dB impedance bandwidth of 2.1%, as well as -24 dB and -20 dB null depths on the elevation and azimuth planes, respectively, in the difference mode of operation.
5 May 2021 in IEEE Transactions on Electromagnetic Compatibility
Electrostatic discharge (ESD) failures in high-speed integrated circuits (ICs) cause critical reliability problems in electronic devices. Transient voltage suppressor (TVS) diodes are installed on high-speed I/O traces to improve system-level ESD protection. To protect the circuit, the majority of ESD current must flow into the external TVS diode rather than into the IC, but due to turn- on behavior, the TVS diode may not snap back when needed and the IC's internal protection may take most of the current. These race conditions between the internal and external ESD protection circuits were investigated for a universal serial bus(USB) interface board. The transient turn- on behavior of the on-chip and off-chip protection circuitry was characterized by measurements and by system efficient ESD design (SEED) simulations. The effect of transmission line pulses (TLP pulses) and power supply voltages of different sizes on the response of the protection circuitry were monitored and compared with SEED simulations. SEED models showed good agreement with measurements and were used to study the impact of passive components added to a high-speed trace or within the IC package on the ESD protection response. Results show the importance of properly accounting for the parasitic resistance and inductance between the on-chip diode and off-chip TVS diode, as well as the length of the transmission line when choosing the external TVS device. Results also show that testing must be performed using mid-level events to account for possible problems due to race conditions.
25 October 2019 in IEEE Antennas and Propagation Magazine
2 July 2019 in IEEE Transactions on Antennas and Propagation
A conformal UWB Archimedean spiral antenna on a dielectric hemisphere is investigated theoretically and experimentally. The analysis method, design, and optimization of this type of spherical antennas is performed using an efficient spatial domain method of moments in conjunction with triangular basis functions and asymptotic Green’s functions. A special conformal mapping is used to enhance the impedance bandwidth and axial ratio bandwidth for a circularly polarized spherical spiral antenna. Emphasis is given to the efficient asymptotic approach in spherical multilayered media. To validate the theory, a UWB leaky wave conformal spiral antenna was designed, manufactured, and tested. The measured results indicate a pretty wide-band behavior for this antenna starting from 1.7 GHz to 6 GHz (1.8 octaves) in its input impedance responses. The circular polarization is maintained over 1.26 octave with less than 3-dB AR.
7 June 2022 in IEEE Transactions on Electromagnetic Compatibility
System-efficient electrostatic discharge (ESD) design (SEED) models of a diode and transient voltage suppressor (TVS) were developed to study their transient response in a high-speed input/output interface. Previously reported SEED models were improved to strengthen their convergence stability and facilitate accurate predictions over a wide range of conditions. These improvements were required to accurately capture the race conditions between the TVS and on -chip diode, where the diode's turn on may prevent turn on of the TVS. Simulations and measurements were performed to demonstrate the impact of the ESD pulse's rise time on race conditions. During a race, results showed the worst-case quasi-static diode current could be twice as high for long rise-time pulses than for short rise-times where the TVS does not turn on , and on -chip diode current may be larger at low test voltages than at high test voltages where the TVS does turn on . Adding a small passive impedance between the external TVS and the on -chip diode helps the TVS turn on and reduce the current through the on -chip diode by more than 50%. Similarly, lengthening the trace between the TVS and diode could reduce on -chip diode current by up to a factor of two.
9 July 2020 in IEEE Transactions on Electromagnetic Compatibility
The ability to predict the electric and magnetic fields generated by a component can solve many in-system interference problems before they occur. In this article, methods are presented to predict the high-frequency near electric and magnetic fields from a component using a method of moment approach. The current representation is estimated from a near electric-field scan by solving the electric field integral equation. The reconstruction method was validated with measurements of a test board containing a buffer integrated circuit. The current representation was shown to accurately predict fields at locations both above and to the side of the buffer with less than a 3.5-dB average error. Here, a near-field scan was only performed on a flat plane above the emitter and was used to predict sources to the side of the emitter. To accurately predict fields to the side of the emitter, the current representation must be defined on a surface between the emitter and the prediction location. An error analysis was performed to understand the impact of scan plane parameters, such as the size of the scan plane, the size of the current representation, and the relative distance between the current representation and the estimated fields on prediction accuracy.