Jianchi Zhou

Jianchi Zhou

Auto-generated profile, based on publicly available information

Jianchi Zhou

EMC Laboratory, Missouri University of Science and Technology, Rolla, MO, USA

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 May 2021 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
JMJavad Soleiman Meiguni
Javad Soleiman Meiguni
JZJianchi Zhou
Jianchi Zhou
GMGiorgi Maghlakelidze
Giorgi Maghlakelidze
YXYang Xu
Yang Xu
OIOmid Hoseini Izadi
Omid Hoseini Izadi
DPDavid Pommerenke
David Pommerenke
Electrostatic discharge (ESD) failures in high-speed integrated circuits (ICs) cause critical reliability problems in electronic devices. Transient voltage suppressor (TVS) diodes are installed on high-speed I/O traces to improve system-level ESD protection. To protect the circuit, the majority of ESD current must flow into the external TVS diode rather than into the IC, but due to turn- on behavior, the TVS diode may not snap back when needed and the IC's internal protection may take most of the current. These race conditions between the internal and external ESD protection circuits were investigated for a universal serial bus(USB) interface board. The transient turn- on behavior of the on-chip and off-chip protection circuitry was characterized by measurements and by system efficient ESD design (SEED) simulations. The effect of transmission line pulses (TLP pulses) and power supply voltages of different sizes on the response of the protection circuitry were monitored and compared with SEED simulations. SEED models showed good agreement with measurements and were used to study the impact of passive components added to a high-speed trace or within the IC package on the ESD protection response. Results show the importance of properly accounting for the parasitic resistance and inductance between the on-chip diode and off-chip TVS diode, as well as the length of the transmission line when choosing the external TVS device. Results also show that testing must be performed using mid-level events to account for possible problems due to race conditions.

1 August 2017
Verified
Conference Paper
Closed access
SYSen Yang
Sen Yang
JZJianchi Zhou
Jianchi Zhou
DPDavid Pommerenke
David Pommerenke
DLDazhao Liu
Dazhao Liu
The transfer impedance of a current probe is typically not constant within the current probe's operational frequency range. As it is based on induction, it will suffer from reduced sensitivity at lower frequencies. Thus, a current probe cannot be used directly in a time domain measurement. The low frequency roll-off of a current probe can severely distort the actual waveform. A simple frequency response compensation method is proposed here to enable ESD current measurements with current probes. The method enables a current probe to be used for time domain measurements, such as when measuring ESD transient current and estimating the total transferred charge. If a probe's datasheet provides the transfer impedance for the probe, no additional measurements are needed. Advantages and disadvantages of directly using the measured complex transfer impedance, instead of approximating the transfer impedance by a circuit, is discussed in this paper.

18 January 2018 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
JZJianchi Zhou
Jianchi Zhou
KGKaustav Ghosh
Kaustav Ghosh
SXShaojie Xiang
Shaojie Xiang
XYXin Yan
Xin Yan
AHAhmad Hosseinbeig
Ahmad Hosseinbeig
DPDavid Pommerenke
David Pommerenke
The core difference between the posture assumed for IEC 61000-4-2 human metal discharge and a discharge to a wearable device is the impedance between the charged body and the grounded structure discharged to. Especially for a waist-worn device, a larger portion of the body is close to the grounded structure; thus the geometry forms much lower impedance which will lead to higher currents. Despite the variability for the air discharge, in most cases, the current will be higher than 3.75 A/kV as specified for contact mode electrostatics discharge (ESD) calibration. Even for the most slowly rising discharges having a spark length equal to the value given by Paschen's law, a 10 kV ESD from the waist will surpass 37.5 A for a waist-worn metal part discharged (e.g., to a door frame). Modeling the wearable device discharge provides predictions on the current derivative and the transient field a wearable device is subjected to. Observed failure levels of a wearable electronic device and comparing discharges according to the IEC 61000-4-2 test standard against discharges from the device while wearable showed that the IEC set-up may be insufficient to ensure the robustness of the wearable devices.

7 June 2022 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
JZJianchi Zhou
Jianchi Zhou
YXYang Xu
Yang Xu
SBSergej Bub
Sergej Bub
SHSteffen Holland
Steffen Holland
JMJavad Soleiman Meiguni
Javad Soleiman Meiguni
DBDaryl G. Beetner
Daryl G. Beetner
System-efficient electrostatic discharge (ESD) design (SEED) models of a diode and transient voltage suppressor (TVS) were developed to study their transient response in a high-speed input/output interface. Previously reported SEED models were improved to strengthen their convergence stability and facilitate accurate predictions over a wide range of conditions. These improvements were required to accurately capture the race conditions between the TVS and on -chip diode, where the diode's turn on may prevent turn on of the TVS. Simulations and measurements were performed to demonstrate the impact of the ESD pulse's rise time on race conditions. During a race, results showed the worst-case quasi-static diode current could be twice as high for long rise-time pulses than for short rise-times where the TVS does not turn on , and on -chip diode current may be larger at low test voltages than at high test voltages where the TVS does turn on . Adding a small passive impedance between the external TVS and the on -chip diode helps the TVS turn on and reduce the current through the on -chip diode by more than 50%. Similarly, lengthening the trace between the TVS and diode could reduce on -chip diode current by up to a factor of two.

1 February 2018 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
AHAhmad Hosseinbeig
Ahmad Hosseinbeig
OIOmid Hoseini Izadi
Omid Hoseini Izadi
SSSudarshan Solanki
Sudarshan Solanki
TLTejasweeni D. Lingayat
Tejasweeni D. Lingayat
BSBala P. Subramanya
Bala P. Subramanya
DPDavid Pommerenke
David Pommerenke
An analysis methodology is presented to investigate soft failures in electronic devices. This methodology combines transmission line pulse (TLP) full-wave simulations with system-level and TLP measurements. Information on susceptible parts in the device under test (DUT) and/or soft failure sensitivity of the integrated circuits (ICs) are obtained from the measurements. Then, the TLP current spreading within the printed circuit board (PCB) of the DUT is simulated. The susceptible signals can be determined by comparing the simulated voltages and/or currents at the signal terminations with the measured threshold values. If the simulated voltages and/or currents are higher than the threshold values, the signal is considered susceptible and a soft failure may occur in the DUT. Using the obtained information from simulations and measurements, the root causes of soft failures can be identified. Further, by utilizing full-wave simulations, the design of the product can be modified to reduce the electrostatic discharge (ESD) noise on the susceptible signals, and consequently prevent soft failures. The proposed analysis methodology is applied to a tablet which suffers from soft failure. The root cause of the soft failure is identified, and countermeasures are designed against the ESD-induced soft failure.

5 January 2023 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
YXYang Xu
Yang Xu
JZJianchi Zhou
Jianchi Zhou
SBSergej Bub
Sergej Bub
SHSteffen Holland
Steffen Holland
JMJavad Soleiman Meiguni
Javad Soleiman Meiguni
DBDaryl G. Beetner
Daryl G. Beetner
Integrated circuits (ICs) connected to a universal serial bus (USB) interface require robust electrostatic discharge (ESD) protection strategies due to the nature of the high-speed interface and the regular access by users. System-efficient ESD design (SEED) simulations can help predict the level of ESD stress seen by the IC when protected by a transient voltage suppressor (TVS). In the following paper, previously developed models were improved to predict the voltage and current seen by a TVS and an on-chip protection diode when an ESD gun was discharged to one USB cable pin. Models were improved, in part, by accurately modeling the conductivity modulation within the behavioral TVS model and by using a measured equivalent source to represent the complex interaction between the ESD gun, USB cable, and enclosure. The response of the TVS and on-chip diode was studied in simulation and measurement for several cable configurations and when adding passive components between the TVS and on-chip diode. Simulations predicted peak and quasi-static voltages and currents at the TVS and on-chip diode within 30% of those seen in measurements. The proposed modeling process can help engineers to evaluate and optimize the effectiveness of their ESD protection strategies under complicated test conditions.