This letter proposes an undersea simultaneous wireless power and data transfer (SWPDT) system with extended communication distance and 1-Mb/s full-duplex communication. The proposed system operates in inductive power transfer-electric field communication mode, thus reducing the crosstalk between the power channel and communication channel. This letter proposes a novel communication channel construction method based on the single capacitor coupling principle, which can effectively extend the communication distance without additional mechanisms. The extended communication distance enables precommunication before charging and maintaining communication after completing charging, which is critical for undersea dynamic equipment. The resonant condition and transmission characteristics of the communication channel are analyzed. Two MHz communication bands are constructed to achieve full-duplex communication based on frequency division duplexing. Finally, the proposed undersea SWPDT prototype has a maximum output power of 1.2 kW and can maintain 1-Mb/s full-duplex communication within a range of 50 cm.
26 July 2023 in IEEE Transactions on Industrial Informatics
In this article, an underwater simultaneous wireless power and data transfer (SWPDT) system with 1-Mbps full-duplex communication link is proposed. The communication channel shares the coupler with the power channel without using additional communication coils. The transducers inject and extract high-frequency data carriers through the taps of the coupling coils to send and receive data. The proposed method for constructing a full-duplex communication channel no longer pursues the resonant relationship between inductance and capacitance. It takes advantage of the inherent characteristics of the higher-order circuit to simplify the circuit structure and maintain a high degree of design freedom. In addition, the center frequencies of the two communication channels do not shift with the change in the transmission distance, realizing the capability of misalignment tolerance. To improve the utilization efficiency of the communication frequency bands and achieve a high data rate, the system uses the minimum shift keying (MSK) modulation and coherent demodulation implemented by Xilinx Zynq-7000 FPGA. A 1-kW underwater SWPDT prototype with 1-Mbps full-duplex communication is presented to demonstrate the proposed system.
8 January 2024 in IEEE Transactions on Industrial Informatics
This article proposes a simultaneous wireless power and data transfer system with full-duplex multiple-input multiple-output (MIMO) communication channels for underwater applications. The system uses power coils to transfer information without additional antennas. Two independent communication channels are constructed, which form $2\times 2$ MIMO communication channels. The data rate is doubled compared with the system with only a single communication channel. So a dedicated channel can be assigned from the two channels to transfer high-priority information, such as control signals and feedback signals, thereby improving communication reliability. Moreover, using two channels can also enhance communication speed. Data can be transferred in parallel on these two channels. To create two communication channels, transceivers load high-frequency carriers onto the coils using two taps for each power coil, resulting in a communication channel with a significantly high-order circuit. In addressing the challenge of designing high-order circuits, this article proposes the reduced-order model for the communication channel. Finally, a 1.1-kW prototype was built with two 1 Mbps full-duplex channels and a total transmission rate of 2 Mbps to verify the feasibility.
11 July 2025 in IEEE Transactions on Industrial Electronics
Due to the high electrical conductivity of seawater, eddy current loss are a critical factor in reducing the transmission efficiency of undersea wireless power transfer (UWPT) systems. This article proposes a method based on impedance matching to enhance transmission efficiency and reduce eddy current loss. The soft-switching and constant output characteristics of four common topologies in undersea applications are comprehensively analyzed in this article. And the advantages of the LCC–LCC topology in UWPT systems are presented. The analysis reveals that the required impedance matching varies with different distances. To improve system adaptability, an active impedance matching technique is employed using the dual active bridge topology with dual-side control and triple-phase shift modulation. Based on the UWPT system model, this article proposes the control strategy to achieve the goals of optimizing transmission efficiency and stabilizing output voltage. To address harmonic currents in the rectifier bridge input caused by secondary-side LCC compensation, this article proposes a model predictive control (MPC) implementation method for active rectifier, while accounting for harmonics and triple-phase shift modulation, aiming to enhance transmission efficiency and achieve precise output voltage regulation. Finally, a 700 W prototype with a transmission efficiency of 93.49% is presented to demonstrate the feasibility of the proposed method.
3 June 2025 in IEEE Transactions on Circuits and Systems II: Express Briefs
The wireless charging process for lithium batteries involves two key phases: constant current (CC) mode and constant voltage (CV) mode. This letter introduces a novel method for topology reconfiguration, simplifying the CC and CV conversion with the control of a single secondary-side switch. The system leverages a three-coil structure for CC output and employs a single switch to reconstruct the two secondary coils, achieving CV output. This approach stands out from previous solutions that required primary control and multiple switches. Using a single switch on the secondary side significantly simplifies the system control and eliminates the necessity for communication with the primary side. These improvements contribute to heightened system reliability. To validate this concept, a prototype with a maximum output of 1.2 kW was developed and tested.
5 December 2025 in IEEE Transactions on Power Electronics
This article addresses the need for multiple critical parameters identification in undersea wireless power transfer (UWPT) systems, where high and variable sea conductivity significantly impacts impedance and renders unreliable premeasurement. So we propose a method to identify primary/secondary coil impedances and mutual impedance during system startup. Furthermore, a novel primary phase acquisition technique using a low-latency simultaneous power and data transmission channel is presented. This is essential because the phase difference between primary and secondary currents in UWPT systems, which deviates from 90$^\circ$ at full resonance, is influenced by the mutual impedance. Furthermore, a double synchronous reference frame model of the UWPT system is established. By utilizing this model for power analysis in conjunction with the primary-side phase information, the proposed approach achieves effective parameter identification.