Yee-Chyan Tan

Yee-Chyan Tan

Auto-generated profile, based on publicly available information

Yee-Chyan Tan

Department of Electronic Engineering, Faculty of Engineering and Green Technology, Universiti Tunku Abdul Rahman, Kampar, Perak, Malaysia

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 February 2025 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
YTYee-Chyan Tan
Yee-Chyan Tan
HRHarikrishnan Ramiah
Harikrishnan Ramiah
SHS. F. Wan Muhamad Hatta
S. F. Wan Muhamad Hatta
CLChee-Cheow Lim
Chee-Cheow Lim
RMRui P. Martins
Rui P. Martins
YCYong Chen
Yong Chen
This brief presents an output-capacitorless low-dropout (OCL-LDO) regulator based on flipped-voltage-follower (FVF) and dual pMOS pass transistors. An adaptive-compensation buffer (ACB) dynamically regulates the operation of the pass transistors. Specifically, when the load current falls below 5 mA, only the smaller pass transistor is activated; otherwise, both pass transistors are engaged, thereby simultaneously mitigating the minimum load current requirement for FVF architecture and extending the load current ranging from 0 to 30 mA while maintaining stability without an external load capacitor. At 1.15-V supply voltage and 0-mA load current, the quiescent current is $6~\mu $ A. The output voltage is 1.0 V with a dropout voltage of 0.15 V. Measurements show that with a load current stepping from 0 to 30 mA at an edge time of 100 ns, the output voltage undershoot is 0.2 V with a recovery time of 200 ns while achieving a load regulation of 0.23 mV/V. Our OCL-LDO is fabricated in a 180-nm CMOS with an active area of 0.031 mm2.

4 April 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YTYee-Chyan Tan
Yee-Chyan Tan
HRHarikrishnan Ramiah
Harikrishnan Ramiah
SHSharifah Fatmadiana Wan Muhamad Hatta
Sharifah Fatmadiana Wan Muhamad Hatta
NLNai Shyan Lai
Nai Shyan Lai
CLChee-Cheow Lim
Chee-Cheow Lim
YCYong Chen
Yong Chen
This article presents an output-capacitorless low-dropout regulator (OCL-LDO), merging with a hybrid push–pull buffer. The hybrid push–pull buffer implements a dynamic and adaptive biasing push–pull gate driving circuit, achieving stability without needing a complex compensation circuit and external load capacitor. Our devised OCL-LDO can operate with a load current range of 0–30 mA, with a quiescent current of 7 μA at zero load current. The proposed OCL-LDO is fabricated in a 0.18-μm CMOS process with an active area of 0.03 mm2. Measurement results show that with a load current stepping from 0–30 mA and an edge time of 100 ns, the output voltage undershoot is 0.14 V, with a corresponding recovery time of 150 ns. The measured load regulation is 0.207 mV/mA at a supply voltage of 1.15 V and a dropout voltage of 0.15 V.

26 March 2026 in IEEE Access
Verified
Journal Article
Open access
KNKhang Yian Ng
Khang Yian Ng
HRHarikrishnan Ramiah
Harikrishnan Ramiah
THTian Siang Ho
Tian Siang Ho
YLYi Chen Lee
Yi Chen Lee
TCTeck Seong Chang
Teck Seong Chang
YCYong Chen
Yong Chen
This paper presents a review of the capacitive cold start-up charge pump (CSUCP) architectures and the design challenges for ultra-low voltage energy harvesting systems. In addition to the surveyed implementations, the underlying operating principles and design concepts of each approach are explained in detail. This study further reviews and consolidates analytical models related to subthreshold conduction, charge transfer, and loss mechanisms. An overview of the oscillator and charge pump interaction is provided as structured design guidance for CSUCP selection and optimization. Key performance tradeoffs, including minimum start-up voltage, voltage conversion efficiency, power conversion efficiency, and start-up robustness, are systematically examined across different CSUCP mechanisms. To illustrate practical design constraints, temperature-dependent simulations adapting the representation of Dickson and cross-coupled charge pump topologies are included to observe environmental variation effects on subthreshold conduction and leakage behavior. By evaluating the relation of architectural mechanisms with analytical design considerations, this review clarifies how different CSUCP techniques address specific performance bottlenecks and provides a unified perspective to support informed CSUCP design under constrained energy conditions.

24 November 2025
Verified
Conference Paper
Closed access
KNKhang Yian Ng
Khang Yian Ng
HRHarikrishnan Ramiah
Harikrishnan Ramiah
KTKai Song Tan
Kai Song Tan
YTYee-Chyan Tan
Yee-Chyan Tan
GCGabriel Chong
Gabriel Chong
This paper presents a MOS-resistor-only threshold (VTH) reference circuit operating from a $0.6-2 \mathrm{V}$ supply in a 130NM CMOS process. Unlike traditional bandgap reference circuits (BGRs), which rely on bipolar BJT devices and typically require ${\geqslant} {1.2} \mathrm{V}$ supply voltage to ensure proper biasing and headroom for analog blocks such as op-amps and current mirrors [3], the proposed design achieves a low reference voltage of 365 mV without curvature compensation or startup circuitry. A key innovation is the use of an active feedback mechanism that suppresses channel-length modulation (CLM) effects, ensuring drain-source voltage matching in the PTAT core. This technique improves current mirroring accuracy and VREF stability, even under low-nm process nodes where CLM effects are more pronounced. Simulation results validate the robustness of the design across supply and temperature variations.

24 November 2025
Verified
Conference Paper
Closed access
PCPei Jie Chan
Pei Jie Chan
HRHarikrishnan Ramiah
Harikrishnan Ramiah
YTYing Yin Teo
Ying Yin Teo
YTYee-Chyan Tan
Yee-Chyan Tan
GCGabriel Chong
Gabriel Chong
This paper presents a high-accuracy, supplycompensated current reference circuit operating from a 1.2-1.8 V supply in a 130NM Complementary Metal-Oxide-Semiconductor (CMOS) process. The proposed design achieves a line sensitivity of 762.48 ppm/V and temperature coefficients (TC) of $2423.42 \text{ppm} /{ }^{\circ} \mathrm{C}$ and $2290.02 \text{ppm} /{ }^{\circ} \mathrm{C}$ over temperature ranges of 0 °C to 70 °C and $-25^{\circ} \mathrm{C}$ to 125 °C, respectively—unlike conventional current reference circuits, which are unable to compensate for both supply and temperature variations simultaneously. By implementing a self-biased current source based on a beta-multiplier circuit, the design minimizes the effect of input voltage fluctuations on the output current while maintaining power consumption below twice the reference current. The robustness of the design across supply and temperature variations is verified by the simulation results presented in this paper.