Wei Wu

Wei Wu

Auto-generated profile, based on publicly available information

Wei Wu

School of Electrical and Electronic Engineering, North China Electric Power University, Beijing, China

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 September 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
JWJian Wang
Jian Wang
WWWei Wu
Wei Wu
YSYuxuan Song
Yuxuan Song
CHChengzhi Hou
Chengzhi Hou
HRHanwen Ren
Hanwen Ren
QLQingmin Li
Qingmin Li
IGBT (insulated gate bipolar transistor) module is prone to the along-surface discharge at the silicone gel-metal electrode-AlN ceramic substrate, that is, the “triple bonding point”, resulting in insulation breakdown, so it is important to develop high-performance silicone gel. In this paper, the composite materials with different contents of 4,4’ -dichlorobenzophenone (DCBP) are prepared and their trap distribution and along-surface discharge characteristics are investigated. The results show that the introduction of DCBP reduces the density of deep trap, increases the density of shallow trap and the degree of crosslinking, is more conducive to the detrapping and migration of charge, and accelerates the attenuation of the surface potential of the composite. Under the condition of sinusoidal voltage of 7 kV and frequency of 10 kHz, the composite material can effectively inhibit the development of the along-surface discharge compared with PSG, and the total discharge times are reduced by 65.08%, 48.71% and 18.27%, respectively. The total discharge range decreases by 69.15%, 62.87% and 22.88%, and the average discharge range decreases by 25.61%, 27.63% and 5.64%, respectively. The release of ultraviolet energy during along-surface discharge excites DCBP to a triplet state, promotes the improvement of crosslinking degree and the generation of new re-crosslinking products, prevents the growth of local low-density insulation region, and further inhibits the occurrence of the along-surface discharge, which enhances the insulation performance of the composite.

10 January 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
JWJian Wang
Jian Wang
WWWei Wu
Wei Wu
YSYuxuan Song
Yuxuan Song
WWWei Wang
Wei Wang
HRHanwen Ren
Hanwen Ren
QLQingmin Li
Qingmin Li
As high-voltage and high-power electronic devices such as insulated gate bipolar transistors (IGBTs) develop towards higher levels, the generated heat and operating temperature rise rapidly, causing the problem of insulation packaging failure to become more serious. In this paper, to study the gas production mechanism of the high-temperature thermal cracking reaction of silicone gel material, the thermogravimetric-infrared spectroscopy (TG-IR), thermogravimetric-mass spectrometry (TG-MS), pyrolysis gas chromatography-mass spectrometry (Py-GC-MS), and molecular dynamics simulation are used to test and simulate the changes of functional groups, thermal cleavage products, and minor molecule gases during the high-temperature thermal cleavage of silicone gel with temperature in an argon atmosphere. Research indicates that under the action of high temperature, the thermal cracking reaction of silicone gel begins at about 330 °C, and the degree of reaction reaches its maximum at about 561 °C. The main products of high-temperature thermal cracking of silicone gel contain two parts: (1) H 2 , CH 4 , C2H6, C 2 H 4 , CO 2 , H 2 O, H 4 Si, CH 2 O and other small molecular gases. From the microscopic level analysis, CH 2 O is the first to be produced in the thermal cracking process of silicone gel than other oxygen-containing gases, and the source of oxygen comes from independent chain breakage. Therefore, the generation of CH 2 O means that the structural quality of silicone gel has changed, which will lead to the failure of insulation package. If H 2 O, CO 2 , and other oxygen-containing gases are generated, it means that the failure of insulation package will be aggravated. (2) The macromolecular products are mainly cyclosiloxanes, esters, aldehydes, alcohols, acids, and other functional organics. The generation of minor molecular gases during thermal decomposition primarily originates from reactions within the side chain groups. Therefore, changing in the side chain structure can enhance the thermal resistance of silicone gel. The conclusions drawn in this paper can offer a specific theoretical basis for monitoring insulation fault gases in silicone gel to encapsulate high-voltage and high-power semiconductor devices.

9 July 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
JWJian Wang
Jian Wang
YSYuxuan Song
Yuxuan Song
WWWei Wu
Wei Wu
HRHanwen Ren
Hanwen Ren
Liang ZouLiang Zou
Liang Zou
QLQingmin Li
Qingmin Li
As a vital component during unit operation, the anti-corona layer and the main insulation composite interface of the variable speed pumped storage generator’s rotor winding are crucial for the safety of the entire hydroelectric system. This research presents a simulation of the prototypical defect types that may arise during the manufacture and operational placement of such rotor windings. An analysis of six interface defect structures within the winding’s anti-corona layer and main insulation composite interface—specifically bubbles, air gaps, water droplets, water films, metal particles, and metal spikes—was conducted. Using an electric field simulation model developed for these rotor winding composite insulation interface defects, the patterns of electric field changes at the composite insulation interface under different defect scenarios were examined. The findings indicate that under a 3kV low-frequency square-wave voltage stress, the maximum electric field intensity distortions at the composite insulation interface caused by bubble and air gap defects are approximately 4.57×10 5 V/m and 9.7×10 5 V/m, respectively. It was observed that as bubble defects increase in size, there’s a marginal reduction in electric field distortion. For water droplet and water film defects, the greatest distortion electric fields are identified as 4.04×10 5 V/m and 1.04×10 6 V/m, correspondingly. The increase in size of water droplets and films resulted in decreases in maximum distortion fields by 27.2% and 93%, respectively. Metal particle and spike impurities produced the most extreme distortion in electric fields, with maximum values at 1.06×10 6 V/m and 1.38×10 6 V/m. Relative to other defect types, the distortions caused by metallic contaminants at the composite insulation interface were found to be the most severe. The research results can make up for the shortcomings of experimental investigation, and have important reference value for winding fault analysis, operation and maintenance, and structural design.

8 September 2025 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
XLXianfeng Li
Xianfeng Li
WWWei Wu
Wei Wu
SLShihua Lan
Shihua Lan
JWJingrui Wang
Jingrui Wang
JWJian Wang
Jian Wang
In order to investigate the impact of low air pressure environment on the device package insulation performance, this paper analyzes the mechanism of “gel-solid” discharge along the surface of the device package insulation under low air pressure and the material damage characteristics. The results show that, based on the analysis of the “solid-liquid” two-phase properties of the silicone gel, with the decrease of air pressure, the “gel-solid” onset discharge electric field (Einc) and the relative permittivity of the silicone gel decrease, resulting in a decrease in the onset voltage of the on-surface discharge. The number and magnitude of discharges in low-pressure environments are strongly influenced mainly by the minimum discharge electric field strength (Emin). The low air pressure promotes an increase in the nucleation rate of bubbles, leading to an increase in the number of bubbles generated, and at the same time, the volume of the gas inside the bubble expands as the air pressure decreases, which promotes an increase in the radius of the bubbles and an increase in the rate of expansion. The lower the air pressure, the more severe the damage to the surface of the material and the more significant the changes in its elemental content and functional groups. This study can provide guidance for the insulation reliability of high-power electric and electronic devices and the design optimization of voltage-resistant power devices in high-altitude areas.