Isil Birlik

Isil Birlik

Auto-generated profile, based on publicly available information

Isil Birlik

Faculty of Engineering Department of Metallurgical and Materials Engineering Dokuz Eylul University Buca İzmir 35390 Türkiye

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 October 2016 in Frontiers in Materials
Verified
Journal Article
Open access
PDF file
IBIsil Birlik
Isil Birlik
NAN. Funda Ak Azem
N. Funda Ak Azem
MTMustafa Toparli
Mustafa Toparli
ECErdal Celik
Erdal Celik
TDTulay Koc Delice
Tulay Koc Delice
TDTuncay Dikici
Tuncay Dikici
In this paper Ni-TiO2 nanocomposite coatings with different sizes of TiO2 nanoparticles were successfully prepared by electrodeposition process from a nickel electrolyte in which the TiO2 nanoparticles were suspended. The influence of relevant deposition parameters on the nanocomposite coating characteristics was discussed. X-ray diffractometer (XRD) has been applied in order to investigate the phase structure of the nanocomposite coatings. The surface morphology of nanocomposite coatings was characterized by a scanning electron microscopy equipped with an energy dispersive spectroscopy (SEM/EDS). The electrodeposited nanocomposite coatings obtained at different deposition parameters were evaluated for their mechanical and corrosive properties. Obtained results show that the size of TiO2 nanoparticles and applied current density during deposition process has a direct effect on mechanical and corrosive properties of nanocomposite coatings. Increasing current density and smaller nanoparticle size has affirmative effect on mechanical properties whereas corrosion resistance of nanocomposite coatings deposited at 3 A.dm-2 current density are higher than the coatings prepared at higher current density values.

3 November 2017 in Coatings
Verified
Journal Article
Open access
PDF file
TMThomas Monsees
Thomas Monsees
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem
Cosmin Mihai CotrutCosmin Mihai Cotrut
Cosmin Mihai Cotrut
Mariana BraicMariana Braic
Mariana Braic
RARadwan Abdulgader
Radwan Abdulgader
Alina Vladescu (Dragomir)Alina Vladescu (Dragomir)
Alina Vladescu (Dragomir)
This study aims to analyze hydroxyapatite (HAP) coatings enriched with Mg and Ti prepared by a magnetron sputtering technique on Ti6Al4V substrate. For preparation of the coatings, three magnetron targets (HAP, MgO and TiO2) were simultaneously co-worked. The concentration of Mg added was varied by modifying the power applied to the MgO target. In all coatings, the Ti concentration was maintained constant by keeping the same cathode power fed during the whole deposition. The influence of different Mg dopant contents on the formation of phase, microstructure and morphology of the obtained Ti-doped HAP coatings were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Moreover, the effects of Mg addition upon corrosion, mechanical and biological properties were also investigated. Mg- and Ti-doped HAP coating obtained at low radio-frequency (RF) power fed to the MgO target provided material with high corrosion resistance compared to other coatings and bare alloy. A slight decrease in hardness of the coatings was found after the Mg addition, from 8.8 to 5.7 GPa. Also, the values of elastic modulus were decreased from 87 to 53 GPa, this being an advantage for biomedical applications. The coatings with low Mg concentration proved to have good deformation to yielding and higher plastic properties. Biological test results showed that the novel surfaces exhibited excellent properties for the adhesion and growth of bone cells. Moreover, early adherent vital cell numbers were significantly higher on both coatings compared to Ti6Al4V, suggesting that Mg ions may accelerate initial osteoblast adhesion and proliferation.

25 February 2020 in Bulletin of Materials Science
Verified
Journal Article
Closed access
PDF file
IBI Birlik
I Birlik
DDD Dagdelen
D Dagdelen

26 August 2022 in Optical Materials
Verified
Journal Article
Closed access
BYBeyza Yildirim
Beyza Yildirim
OKOzgur Yasin Keskin
Ozgur Yasin Keskin
RDRamazan Dalmis
Ramazan Dalmis
IBIsil Birlik
Isil Birlik
FAFunda Ak Azem
Funda Ak Azem
KEKadriye Ertekin
Kadriye Ertekin

25 February 2021 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
RDRamazan Dalmis
Ramazan Dalmis
IBIsil Birlik
Isil Birlik
NAN. Funda Ak Azem
N. Funda Ak Azem
ECErdal Celik
Erdal Celik

1 November 2024 in Materials Research Express
Verified
Journal Article
Open access
SGSerdar Gültekin
Serdar Gültekin
IBIsil Birlik
Isil Birlik
SOSibel Oguzlar
Sibel Oguzlar
KEKadriye Ertekin
Kadriye Ertekin
This study explored the superior photocatalytic performance of the nanoscale zinc oxide-yttrium oxide (ZnO-Y2O3) based composite over ZnO nanoparticles (NPs). We investigated this by following the photocatalytic degradation efficiency of methylene blue (MB). The sol–gel synthesized Y2O3 and ZnO NPs were characterized by x-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The spectral behaviour and photocatalytic efficiency of the proposed composite were investigated by UV–vis spectrophotometry, steady-state and time-resolved photoluminescence (PL) measurements, respectively. The results indicated the successful formation of Y2O3 and ZnO nanoparticles with desirable structural properties. The photocatalytic degradation efficiency of the MB solution was evaluated for different concentrations of the counterparts of the ZnO-Y2O3 composite. In particular, the ZnO-5Y2O3-based composite showed superior photocatalytic activity after 150 min of UV irradiation, achieving 98.4% degradation of the MB solution compared to the 77% degradation achieved by pure ZnO. Although Y2O3 alone does not exhibit photocatalytic activity, its combination with ZnO significantly enhances the photocatalytic performance of ZnO. This improvement was attributed to the luminescence properties of Y2O3. By elucidating this unique mechanism, the performance of photocatalytic materials can be significantly enhanced. In our study, the improvement of the photodegradation rate constant (kapp) of ZnO from 0.009 min−1 to 0.0242 min−1 demonstrated the promising photocatalytic efficiency of the ZnO-5Y2O3 based composite, opening up exciting possibilities for further applications in environmental remediation and other fields.