13 July 2020 in IEEE Transactions on Microwave Theory and Techniques
In this article, a new bandpass distributed amplifier (DA) using a wideband gain-boosting technique is presented. In particular, a feedback network, including a series inductor and a shunt capacitor, is used to generate two peaks at the lower and upper cutoff frequencies of the amplifier's bandpass response. This technique provides a gain enhancement over a wide bandwidth without sacrificing the upper cutoff frequency. A detailed analysis of the two frequencies peaking effect is carried out to support the theory. To verify the concept, a conventional and a gain-enhanced DA are fabricated in an indium-phosphide (InP) heterojunction bipolar transistor (HBT) process. The gain-enhanced DA exhibits a measured gain of 10.5 dB with a 4-dB gain improvement compared with the conventional one, covering a 3-dB bandwidth from 60 to 145 GHz. The maximum saturated (Psat) is 20.9 dBm at 75 GHz with the measured 1-dB compression power (P1dB) of 18.5 dBm. The dc power consumption is 440 mW, and the chip size is 1.6 mm x 0.6 mm. To the best of our knowledge, the proposed DA achieves the highest gain boosting over a broad bandwidth compared with the published works.
24 March 2020 in IEEE Microwave and Wireless Components Letters
A wideband monolithic microwave/millimeter-wave integrated circuit (MMIC) distributed amplifier (DA) using a 3-D interdigital capacitor at the input of the gain cell is demonstrated in an indium phosphide (InP) heterojunction bipolar transistor (HBT) process. The proposed DA using interdigital capacitors improves the input return loss at high frequencies compared with the one implemented with conventional metal-insulator-metal (MIM) capacitors. The fabricated amplifier achieves a measured average gain of 10.5 dB over a 3-dB bandwidth from 1 to 160 GHz. The maximum measured saturated power (Psat) is 17.8 dBm with the corresponding 1-dB compression power (P1,dB) of 15 dBm at 55 GHz. The amplifier achieves a minimum Psat of 14.6 dBm up to 110 GHz.
12 March 2020 in IEEE Transactions on Microwave Theory and Techniques
In this article, a wideband linearization technique for distributed amplifiers (DAs) is presented. In particular, an auxiliary transistor is employed to create additional intermodulation distortion components that will be feed-forwarded to the output of each gain unit cell to significantly suppress the third-order intermodulation (IM3) distortion. To verify the concept, two DAs are fabricated in an indium phosphide (InP) process. One amplifier employs a conventional stacked-heterojunction bipolar transistor (HBT) gain unit cell, and the other linearized amplifier utilizes the proposed technique. The linearized DA exhibits a measured gain of 10.5 dB with a 3-dB gain bandwidth from dc to 90 GHz. The maximum 1-dB gain compression output power (P1 dB) is 20.5 dBm, and the third-order intercept point (OIP3) is 33 dBm. Compared to the conventional amplifier, the two values are improved by 3.5 and 4.5 dB on average, respectively. Moreover, the linearization technique only increases very little dc power consumption at high power and has the same chip size as compared to the conventional design. To the best of the authors' knowledge, compared to published state-of-the-art DAs, the proposed DA achieves among the highest OIP3 over a wide bandwidth.
23 January 2023 in IEEE Microwave and Wireless Technology Letters
In this letter, we present the designs and development of a wideband, high output power quadruple-stacked heterojunction bipolar transistor (HBT) distributed amplifier (DA). In particular, the stacked HBT configuration can improve gain and output power while achieving a very wide bandwidth. To validate the proposed design concept, a quadruple-stacked HBT DA is designed in an indium phosphide (InP) process. The measurement results show an average gain of 16 dB from 7–115-GHz bandwidth with a maximum of 24-dBm saturated output power ( $P_{\mathrm{sat}})$ . To the best of the authors’ knowledge, this is the first time quadruple-stacked HBT is used in a DA to achieve the highest output power compared with other published work in the same frequency range.
11 December 2023 in IEEE Transactions on Microwave Theory and Techniques
This article presents a novel Darlington cell that improves the gain–bandwidth product and output power of distributed amplifiers (DAs). By employing two diode-connected transistors to a conventional Darlington pair, the voltages and currents of two transistors inside the pair are balanced, and output power is improved. Moreover, the new cell’s high input impedance and high current gain allow the DA to have lower input line loss and wider bandwidth. A 3–230-GHz indium phosphide DA is designed and characterized to verify the concept. The Darlington DA prototype provides an average gain of 13 dB over 3–230-GHz bandwidth while keeping input and output return losses below $-$ 7 dB up to 220 GHz. Across several frequency bands from 10–65, 70–110, 110–170, and 170–220 GHz, the average saturated output power is 21.2, 20, 18.5, and 13.3 dBm, respectively. The maximum output 1-dB compression point and third-order intercept point are 17.6 and 30.4 dBm, respectively. The measured peak power-added efficiency is 10.5% at 70 GHz and 5.5% at 170 GHz. The Darlington DA consumes 110 mA from a 6.6-V supply.