Dan G. Zollinger

Dan G. Zollinger

Auto-generated profile, based on publicly available information

Dan G. Zollinger

Department of Civil Engineering, Texas A&M University, College Station, TX

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 May 2015 in Materials and Structures
Verified
Journal Article
Open access
PDF file
NMNoor Masad
Noor Masad
DZDan Zollinger
Dan Zollinger
SKSun-Myung Kim
Sun-Myung Kim
ZGZachary Grasley
Zachary Grasley

1 February 2012 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
SLSang Ick Lee
Sang Ick Lee
DZDan G. Zollinger
Dan G. Zollinger
During the hydration of Portland cement concrete, free water reacts with the compounds of unhydrated cement to form the hydrated phases that make up concrete. The chemical reaction results in a reduction in the amount of free water and consequently produces hydration products. Thus, the estimate of free water content and other components in hardening concrete is very helpful in understanding the behavior of early age concrete and the ultimate quality of concrete that can be achieved. Although many properties of concrete are related to the volume fractions of its components, dielectric properties are a beneficial parameter for identifying characteristic components of hardening concrete over time. They can also serve as a useful and continuous nondestructive measurement technique applicable during the hydration process. This paper defines a volumetric relationship of fresh concrete and describes an approach to estimate the volume fraction of the different phases or components that make up hardening concrete...

1 January 2000 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
LWLi-Gang Wang
Li-Gang Wang
DZDan G. Zollinger
Dan G. Zollinger
Spalling is a distress form in concrete pavements that often manifests as the breakdown of the joint of a slab within 15 cm (6 in.) of the joint or crack and can occur at both longitudinal and transverse joints. Efforts have been under way at Texas A&M University to formulate mechanistic spalling models derived from data gathered in recent Texas Department of Transportation studies related to spall development. Extensive field studies have led to the establishment of a spalling mechanism consisting of a step-by-step process that can be characterized with engineering mechanics. These findings indicate that spalling is the result of damage initiated in the form of a shear delamination that is oriented parallel to and at a shallow depth below the surface of the pavement. Conditions necessary for formation of the delaminations include low interfacial strength between the aggregate and mortar and sufficient evaporation of pore water from the hydrating concrete, resulting in differential drying shrinkage near the pavement surface. Delaminations have been noted to initiate early in the life of the pavement and, once formed, extend later into spalls as a result of incompressibles, freeze-thaw cycles, traffic loading, and other such effects. A design framework for delamination formation and subsequent spalling development is presented in a practical format in which to mechanistically design concrete pavement systems relative to spalling distress.

10 March 2022 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
JKJinho Kim
Jinho Kim
DZDan Zollinger
Dan Zollinger
WCWoohyun Cho
Woohyun Cho
Joint sealants play an important role in maintaining concrete pavement. They reduce or prevent numerous distresses, including spalling, faulting, and subbase erosion damage. The successful maintenance of such joint sealants is closely linked to a satisfactory lifespan for rigid pavement. However, it has been found that many sealants often fail in the early stages, as a result of inadequate or insufficient joint preparation. This study examined the effects of moisture content on bond strength, the main cause of joint sealant failure. Sealant use in various climatic regions throughout the United States was examined and Departments of Transportation were surveyed with regard to how they handled moisture. The survey showed that in cold-freeze areas, hot-pour sealants were preferred over silicone, and most states visually inspected the moisture condition of joint reservoirs. This research evaluated the effects of surface moisture on the tensile bond strength between a joint sealant and reservoir. In addition, an indirect measurement method was applied to estimate the reduction in bond strength in response to excessive moisture on the reservoir wall at the allowable strain. The causes of degradation in adhesion strength were evaluated by measuring the sealant wetting angle. Finally, it was determined that, while the choice of sealant may depend on the climate, those not currently preferred in wet-freeze regions could be used if accompanied by proper pretreatment and moisture control, contributing to the stable lifespan of joint sealants and concrete pavement alike.

30 August 2021 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
PDF file
IIIssa M. Issa
Issa M. Issa
DZDan G. Zollinger
Dan G. Zollinger
IOIbrahim Onifade
Ibrahim Onifade
RLRobert L. Lytton
Robert L. Lytton
This work deals with using time-domain reflectometry (TDR) to measure the electrical properties of roller compacted concrete (RCC). It is well known that TDR provides a non-destructive method to measure the dielectric constant toward an estimation of moisture content for soil materials. However, few studies have used TDR to determine the moisture content in concrete because of the inability to obtain TDR traces after the concrete hardens. To obtain TDR traces, a transmission circuit is initiated where a wave signal moves through the medium and reflects back in accordance with transmission line theory. In the literature, the TDR waveform has been interpreted empirically to estimate the relative permittivity (or dielectric constant) and electrical conductivity in a given material relative to the determination of associated water content. However, empirical models tend to ignore certain aspects related to the electrical properties of a medium, which has made interpretation of TDR measurements prone to systematic errors. In this paper, a new approach of test configuration and TDR response interpretation has been developed. For the test setup, the approach uses disposable metal probes that can be embedded into the concrete at different depths to obtain the TDR traces. The approach also employs the transmission line equation to estimate the dielectric constant, electrical conductivity, and reflectivity of an instrumented RCC mixture. These properties will affect the understanding of the RCC pavement behavior, especially curling and warping behavior, placement density, and development of long-term distresses.

31 December 2021
Verified
Conference Paper
Closed access
IIIssa Issa
Issa Issa
DZDan Zollinger
Dan Zollinger
Local calibration of the punchout model in the Pavement ME software is a vital step in achieving performance predictability for the design of Continuously Reinforced Concrete (CRC) pavement. In Oklahoma, there was only limited performance data available in the General Pavement Studies (GPS) database for CRC pavement. This set of circumstances required a different approach as to the type of data used for calibration. The type of data originally utilized in NCHRP 1-37A essentially represented visually evident damage that is clearly observable at the surface of the pavement structure. Non-observable damage however is actually of greater value as a source of calibration data since it represents the deteriorative conditions that lead to the visual manifestation of the damage process. Since visually validated distress is the end result of the distress cycle the traffic level associated with it is often subject to a considerable amount of error. In this regard, non-observable data such as erosion damage is shown to be a good indicator of and a substitute for actual punchout data since it represents the deterioration of the slab subbase interface that has be found to closely aligned with the punchout process. The amount of erosion is evaluated based on FWD data and is shown it to be a reliable way to determine the calibration coefficients for the punchout model. This paper proposes an approach for calibrating local coefficients for CRC pavements based on non-observable performance data. The main process of this methodology requires estimating erosion percentage damage using Falling Weight Deflectometer data (FWD), determining the percentage of punchout from the Long-Term Performance Program (LTPP) records, and establishing the relationship between both components to estimate the existing punchout distresses. This relationship can be used to calculate the actual damage including erosion damage and to calibrate the local coefficients used in the pavement ME punchout model. This methodology was carried out on one section from Oklahoma and one section from Texas in order to validate its applicability and conclude on the pavement ME punchout model and its ability to predict punchout distress in the field.