20 April 2018 in IEEE Transactions on Power Electronics
Electric vehicles (EVs) are becoming increasingly popular as a mean of mitigating issues associated with fossil fuel consumption in transportation systems. A wireless inductive power transfer (IPT) interface between EV and the utility grid has several key advantages, such as safety, convenience, and isolation. However, physical misalignments between the pads of IPT charging systems used in EVs are unavoidable and cause variations in key system parameters, significantly increasing losses and affecting power throughput. This paper presents a novel series-hybrid topology in which the series inductors of the primary and pick-up LCL networks are integrated into polarized magnetic couplers to improve the system performance under pad misalignment. A mathematical model is developed to investigate the behavior of the proposed system under misalignment. To demonstrate the viability of the proposed method, the results of a 3.3 kW prototype series-hybrid IPT system are presented, benched marked against a conventional IPT system. Experimental results clearly indicate that the proposed system maintains the output power within μ5% of its rated power despite the pad misalignment. The proposed system is efficient, reliable and cost-effective in comparison to conventional LCL and CL compensated IPT systems.systems.
20 December 2017 in IEEE Transactions on Power Electronics
Wireless power transfer (WPT) is a promising technology for supplying power to various applications with no physical contacts. Recently, bidirectional wireless power transfer (BD-WPT) systems are gaining popularity for grid-to-vehicle and vehicle-to-grid applications which essentially require power transfer in both directions. However, BD-WPT systems are complex in nature, and require sophisticated control strategies to provide synchronization as well as to regulate the power flow between two sides. This paper proposes a new controller that uses measured active power (P) and reactive power (Q) at the resonant network of BD-WPT systems to regulate the power flow in both directions while providing synchronization between two sides without a dedicated communication interface for controlling power transfer. The controller, located on the pickup side, is applicable to BD-WPT systems with either single or multiple loads and ensures that the volt-ampere rating of the pickup converter is at lowest for battery charging, by keeping the reactive power at the resonant tank intake by the load side minimum. Experimental results obtained from a 1-kW prototype system show good agreement with simulated results, validating that the proposed controller can be used to regulate the power flow in BD-WPT systems.
11 February 2021 in IEEE Transactions on Power Electronics
An inductive power transfer (IPT) system is envisaged as the best solution to conveniently charge electric vehicles (EVs). While stationary IPT systems are becoming commercialized, significant research is being conducted to address the challenges related to dynamic IPT systems. Dynamic or in-motion IPT systems require a fully electrified roadway with embedded inductive couplers with accompanying circuitry. The large number of electronic components required, however, increases the system complexity, reducing the reliability and economic viability of dynamic IPT systems proposed to-date. This article proposes a simple yet robust push-pull driven coupler array (PPCA), aiming to decrease the number of switches required to drive the in-road couplers. This article is the first to report a configuration where only N+1 switches are required to independently energize N primary IPT couplers. Any number of couplers can be activated simultaneously in the array without proportionally increasing the current stress on the switches. A state-space model is developed and implemented in PLECS to investigate the efficiency and power transferred to an EV traveling over the proposed PPCA while considering the variation in the coupling and the self-inductances of the couplers. A 3.3-kW scaled prototype PPCA consisting of three primary couplers and two secondary couplers has been implemented to validate the performance of the proposed configuration.
2 February 2021 in IEEE Transactions on Industrial Electronics
In this article, coupled electromagnetic-thermal simulations of inductive power transfer (IPT) pads using finite-element simulations are discussed. Derivation of each electrical and thermal parameters required for the modeling process is outlined. Simulation models are used to predict the power loss and the temperature rise of an IPT pad at different ambient temperatures at steady state. Using these simulation methods, the power loss within an IPT pad operating at 50 ${^\circ }$ C ambient temperature is predicted. A 10-KW IPT system is set up within an environmental chamber to validate the predicted losses within the system.
19 November 2007 in IEEE Transactions on Industrial Electronics
This paper presents a technique for the suppression of voltage transients through the use of dynamically reconfigurable supercapacitor (SC) banks. The technique requires a minimum of two SC banks to transfer power from a mains supply to load in complete isolation. The banks are operated independently as energy-storing elements in one of the three states of charging, discharging, or idling, and transition of banks from one state to another with isolation is realized dynamically by inductively coupled power-transfer technology with no physical contacts. The proposed technique has no direct connection between the mains supply and load at any given moment, and power transfer takes place in complete isolation with built-in protection for both common- and differential-mode transients. Sizing of the banks with respect to various types of SCs and system parameters is analyzed. Comparisons between simulations and experimental results of two prototype systems, subjected to combination transient surges specified by IEC61000-4-5 standard, are presented with a discussion to show the validity of the proposed concept and its suitability for uninterruptible power systems and emergency power supplies.
23 July 2019 in IEEE Transactions on Power Electronics
Bi-directional inductive power transfer (BD-IPT) systems facilitate wireless grid integration of electric vehicles (EVs) to offer vehicle-to-grid (V2G) services. This paper presents a novel push-pull parallel resonant converter (PPRC) based BD-IPT system to provide a more efficient and cost effective solution to wireless V2G technologies. The proposed system integrates the functionality of bulky passive elements into a Double-D type magnetic coupler to achieve high power density. A phase shift control technique is proposed to regulate the power flow between the primary and secondary side of the push-push converters. A zero voltage switching (ZVS) zone is identified to maintain safe operation of the system. Both the operating principles and control philosophy of the converters are described, and a detailed mathematical analysis and modelling is presented. The effectiveness of the proposed system is verified by building a 3.3 kW prototype system. The experimental results show that the peak power transfer efficiency reaches 96.5%, and the efficiency remains high under all ZVS operating conditions.