Realizing high-performance soft robotic grippers is challenging because of the inherent limitations of the soft actuators and artificial muscles that drive them, including low force generation, small actuation range, and poor compactness to name a few. Despite advances in this area, realizing compact soft grippers, which exhibit high dexterity and force output, is still challenging. This article explores using twisted string actuators (TSAs) to drive a soft robotic gripper. TSAs have been widely used in numerous robotic applications, but their inclusion in soft robots has been limited. The proposed design of the gripper was inspired by the human hand, with four fingers and a thumb. Tunable stiffness was implemented in the fingers by using antagonistic TSAs. The fingers' bending angles, actuation speed, blocked force output, and stiffness tuning are experimentally characterized. The gripper achieves a score of 6 on the Kapandji test and recreate 31 of the 33 grasps of the Feix GRASP taxonomy. It exhibits a maximum grasping force of 72 N, which is almost 13 times its own weight. A comparison study reveals that the proposed gripper exhibits equivalent or superior performance compared to other similar soft grippers.
Twisted string actuators (TSAs) convert rotational motion from twisting into linear motion. They are known for high energy efficiency, and large linear strain and stress outputs. Although they have been successfully applied as the moving mechanism for different robot applications, their potential in soft robotics is mainly challenged by two aspects: First, the conventional strings of TSAs are stiff and strong but not compliant. Second, precise control of TSAs predominantly relies on external position or force sensors. Because of these, TSA-driven robots are often rigid and bulky. In this study, we propose the design, modeling, and robotic application of TSAs that are compliant, can produce large strain, and are capable of self-sensing during twisting-induced actuation. The design is realized by replacing conventional stiff strings with compliant, thermally activated, and conductive supercoiled polymer strings. Experiments show that the developed TSAs have normalized stiffness of 30%, and position self-sensing capability during twisting. The quasi-static actuation and self-sensing properties are accurately captured by the Preisach hysteresis operators. In particular, both the twisting-induced actuation and thermally induced actuation are considered. Finally, the proposed TSAs are successfully demonstrated in a low-cost three-dimensionally printed compliant robotic gripper.
2 February 2021 in IEEE Robotics and Automation Letters
Twisted string actuators (TSAs) have exhibited great promise in robotic applications by generating high translational force with low input torque. Despite great success, it remains a challenge to reliably estimate the strain of TSAs using compact solutions while maintaining actuator compliance. The inclusion of position sensors not only increases system complexity but also decreases system compliance, a property often crucial in soft robots. We recently constructed a compliant TSA with self-sensing capability by adopting conductive and stretchable super-coiled polymer (SCP) strings; however, only quasi-static measurements of the strain-resistance correlation were obtained. This study proposes a strategy to experimentally characterize and model the transient self-sensing property in compliant TSAs. The correlation between resistance and strain is characterized under different motor twisting sequences and step durations, and exhibited transient decay, hysteresis, and creep. A self-sensing model that consists of a log-based nonlinear term, a rate-dependent Prandtl-Ishlinskii hysteresis term, and a creep term is proposed for the compliant TSAs. Experimental results confirm the high effectiveness of the proposed self-sensing approach, with the average model validation error less than 0.036 cm.
Realizing high-performance soft robots is challenging because many existing soft or compliant actuators exhibit limitations like fabrication complexity, high power requirement, slow actuation, and low force generation. Due to their high-force output and power efficiency, compactness, and simplicity in fabrication, twisted string actuators (TSAs) have exhibited strong potential in mechatronic and robotic applications. However, they have had limited uses in soft robotics. Consequently, modeling and control of TSA-driven soft robots have not been sufficiently studied. This article presents the first study on the modeling and control of a TSA-driven soft robotic manipulator. A physics-based model was developed to predict the manipulator’s kinematic motion. An inverse model was derived to realize open-loop control. Models that describe the behavior of TSAs were utilized in a novel way to develop the proposed kinematic and inverse models of the soft robot. The proposed modeling and control approaches were experimentally verified to be effective. For example, the modeling and control errors of the bending angle were 1.60 deg (3.11%) and 2.11 deg (3.68%), respectively.
2 November 2023 in IEEE Robotics and Automation Letters
Gripper hardware design often involves a trade-off between distinct and sometimes opposing goals (e.g., high grasping force vs. gentleness). To address this trade-off within a single device, we present a multi-mode gripper with fingers that are scissor linkages, that can actively transform between three distinct modes by varying the number and locations of mechanical singularities. Each of these modes has properties that are suitable for specific needs. Mode 1 provides high grip strength, using a short lever arm and rigid structure. Mode 2 allows precise finger positioning and in-hand manipulation, using two independently controlled DOFs per finger. Mode 3 provides underactuated grasping that can passively adapt to delicate or irregularly shaped objects, with four DOFs per finger. The kinematic relationships, joint torques, and fingertip forces are derived analytically for each of the three modes. Gripper performance and the kinematic model are verified experimentally.
Twisted string actuators (TSAs) have exhibited great promise in robotic applications by generating high translational force with low input torque. To further facilitate their robotic applications, it is strongly desirable but challenging to enhance their consistent strain generation while maintaining compliance. Existing studies predominantly considered overtwisting and coiling after the regular twisting stage to be undesirable—nonuniform and unpredictable knots, entanglements, and coils formed to create an unstable and failure-prone structure. Overtwisting would work well for TSAs when uniform coils can be consistently formed. In this study, we realize uniform and consistent coil formation in overtwisted TSAs, which greatly increases their strain. Furthermore, we investigate methods for enabling uniform coil formation upon overtwisting the strings in a TSA and present a procedure to systematically “train” the strings. To the authors' best knowledge, this is the first study to experimentally investigate overtwisting for TSAs with different stiffnesses and realize consistent uniform coil formation. Ultrahigh molecular-weight polyethylene strings form the stiff TSAs, whereas compliant TSAs are realized with stretchable and conductive supercoiled polymer strings. The strain, force, velocity, and torque of each overtwisted TSA were studied. Overtwisting and coiling resulted in ∼70% strain in stiff TSAs and ∼60% strain in compliant TSAs. This is more than twice the strain achieved through regular twisting. Finally, the overtwisted TSA was successfully demonstrated in a robotic bicep.