Medical Robotics and Automation (RoboMed) Laboratory, Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA, USA
Auto-generated profile, based on publicly available information
Revanth Konda
Medical Robotics and Automation (RoboMed) Laboratory, Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA, USA
Realizing high-performance soft robotic grippers is challenging because of the inherent limitations of the soft actuators and artificial muscles that drive them, including low force generation, small actuation range, and poor compactness to name a few. Despite advances in this area, realizing compact soft grippers, which exhibit high dexterity and force output, is still challenging. This article explores using twisted string actuators (TSAs) to drive a soft robotic gripper. TSAs have been widely used in numerous robotic applications, but their inclusion in soft robots has been limited. The proposed design of the gripper was inspired by the human hand, with four fingers and a thumb. Tunable stiffness was implemented in the fingers by using antagonistic TSAs. The fingers' bending angles, actuation speed, blocked force output, and stiffness tuning are experimentally characterized. The gripper achieves a score of 6 on the Kapandji test and recreate 31 of the 33 grasps of the Feix GRASP taxonomy. It exhibits a maximum grasping force of 72 N, which is almost 13 times its own weight. A comparison study reveals that the proposed gripper exhibits equivalent or superior performance compared to other similar soft grippers.
4 August 2020 in IEEE Robotics and Automation Letters
The nature-inspired behavior of collective motion is found to be an optimal solution in swarming systems for predator avoidance and survival. In this work, we propose a two-level control architecture for multi-robot systems (MRS), which leverages the advantages of flocking control and function approximated reinforcement learning for predator avoidance task. Reinforcement learning in multi-agent systems has gained a tremendous amount of interest in recent few years. Computationally intensive architectures such as deep reinforcement learning and actor-critic approaches have been extensively developed and have proved to be extremely efficient. The proposed approach, comprising of cooperative function approximated Q-learning, is applied such that it ensures formation maintenance in MRS while predator avoidance. A consensus filter is incorporated into the control architecture, to sense predators in close vicinity in a distributed and cooperative fashion to ensure consensus on states among the robots in the system. The proposed approach is proved to be convergent and results in superior performance in unexplored states and reduced number of variables. Simulation results confirm the effectiveness of the proposed approach over existing methods. We expect that the proposed approach can be conveniently applied to many other areas with little modifications, such as fire-fighting robots, surveillance and patrolling robots.
1 February 2022 in Mechanical Systems and Signal Processing
Twisted string actuators (TSAs) have exhibited great promise in robotic applications by generating high translational force with low input torque. Despite great success, it remains a challenge to reliably estimate the strain of TSAs using compact solutions while maintaining actuator compliance. The inclusion of position sensors not only increases system complexity but also decreases system compliance, a property often crucial in soft robots. We recently constructed a compliant TSA with self-sensing capability by adopting conductive and stretchable super-coiled polymer (SCP) strings; however, only quasi-static measurements of the strain-resistance correlation were obtained. This study proposes a strategy to experimentally characterize and model the transient self-sensing property in compliant TSAs. The correlation between resistance and strain is characterized under different motor twisting sequences and step durations, and exhibited transient decay, hysteresis, and creep. A self-sensing model that consists of a log-based nonlinear term, a rate-dependent Prandtl-Ishlinskii hysteresis term, and a creep term is proposed for the compliant TSAs. Experimental results confirm the high effectiveness of the proposed self-sensing approach, with the average model validation error less than 0.036 cm.
Research on robotically steerable guidewires has surged in the past decade because of their potential in addressing difficulties related to endovascular interventions. These microscale devices exhibit unique challenges in design, fabrication, and control, not necessarily present in mesoscale continuum robots such as robotic catheters and endoscopes. Existing literature on surgical robots mainly addresses advancements in robotic surgery with a focus on current trends in specific clinical procedures. Our article aims to bridge this gap by reviewing current clinical practices in endovascular interventions, highlighting the clinical motivations for the development of robotically steerable guidewires, and detailing the current advancements and future prospects in topics related to these devices.
Realizing high-performance soft robots is challenging because many existing soft or compliant actuators exhibit limitations like fabrication complexity, high power requirement, slow actuation, and low force generation. Due to their high-force output and power efficiency, compactness, and simplicity in fabrication, twisted string actuators (TSAs) have exhibited strong potential in mechatronic and robotic applications. However, they have had limited uses in soft robotics. Consequently, modeling and control of TSA-driven soft robots have not been sufficiently studied. This article presents the first study on the modeling and control of a TSA-driven soft robotic manipulator. A physics-based model was developed to predict the manipulator’s kinematic motion. An inverse model was derived to realize open-loop control. Models that describe the behavior of TSAs were utilized in a novel way to develop the proposed kinematic and inverse models of the soft robot. The proposed modeling and control approaches were experimentally verified to be effective. For example, the modeling and control errors of the bending angle were 1.60 deg (3.11%) and 2.11 deg (3.68%), respectively.