Pierre-Antoine Cormier

Pierre-Antoine Cormier

Auto-generated profile, based on publicly available information

Pierre-Antoine Cormier

CESI LINEACT, Campus CESI Orleans,1 Allee Titane, F-45100 Orleans, France

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in Thin Solid Films
Verified
Journal Article
Closed access
JDJ. Dervaux
J. Dervaux
PCP.-A. Cormier
P.-A. Cormier
PMP. Moskovkin
P. Moskovkin
ODO. Douheret
O. Douheret
SKS. Konstantinidis
S. Konstantinidis
RSR. Snyders
R. Snyders

1 October 2013 in Thin Solid Films
Verified
Journal Article
Closed access
PCP.-A. Cormier
P.-A. Cormier
ATA.-L. Thomann
A.-L. Thomann
VDV. Dolique
V. Dolique
ABA. Balhamri
A. Balhamri
RDR. Dussart
R. Dussart
SKS. Konstantinidis
S. Konstantinidis

7 January 2013 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
PCP.-A. Cormier
P.-A. Cormier
ABA. Balhamri
A. Balhamri
ATA.-L. Thomann
A.-L. Thomann
RDR. Dussart
R. Dussart
NSNadjib Semmar
Nadjib Semmar
SKS. Konstantinidis
S. Konstantinidis
In this work, the energetic conditions at the substrate were investigated in dc magnetron sputtering (DCMS), pulsed dc magnetron sputtering (pDCMS), and high power impulse magnetron sputtering (HiPIMS) discharges by means of an energy flux diagnostic based on a thermopile sensor, the probe being set at the substrate position. Measurements were performed in front of a titanium target for a highly unbalanced magnetic field configuration. The average power was always kept to 400 W and the probe was at the floating potential. Variation of the energy flux against the pulse peak power in HiPIMS was first investigated. It was demonstrated that the energy per deposited titanium atom is the highest for short pulses (5 μs) high pulse peak power (39 kW), as in this case, the ion production is efficient and the deposition rate is reduced by self-sputtering. As the argon pressure is increased, the energy deposition is reduced as the probability of scattering in the gas phase is increased. In the case of the HiPIMS discharge run at moderate peak power density (10 kW), the energy per deposited atom was found to be lower than the one measured for DCMS and pDCMS discharges. In these conditions, the HiPIMS discharge could be characterized as soft and close to a pulsed DCMS discharge run at very low duty cycle. For the sake of comparison, measurements were also carried out in DCMS mode with a balanced magnetron cathode, in the same working conditions of pressure and power. The energy flux at the substrate is significantly increased as the discharge is generated in an unbalanced field.

1 September 2014 in Surface and Coatings Technology
Verified
Journal Article
Closed access
PCP.-A. Cormier
P.-A. Cormier
ABA. Balhamri
A. Balhamri
ATA.-L. Thomann
A.-L. Thomann
RDR. Dussart
R. Dussart
NSNadjib Semmar
Nadjib Semmar
SKS. Konstantinidis
S. Konstantinidis

2 November 2010 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
PCPierre-Antoine Cormier
Pierre-Antoine Cormier
MSMarc Stahl
Marc Stahl
ATAnne-Lise Thomann
Anne-Lise Thomann
RDRémi Dussart
Rémi Dussart
MWMatthias Wolter
Matthias Wolter
HKHolger Kersten
Holger Kersten
Two different diagnostics for the determination of the energy influx in plasma processes were used to characterize an ion beam source and an asymmetric RF discharge. The related energy fluxes were measured in dependence on the ion energy and on the RF power, respectively. The first sensor, called HFM (Heat Flux Microsensor) is a thermopile which allows for direct energy flux measurements. With the second sensor, a calorimetric probe, the energy influx has been calculated from the temporal temperature evolution preliminarily registered. Although the working principle of both sensors is different, the obtained results are in good agreement. In the ion beam (<1.5 keV)) rather high energy influxes are achieved (up to 700 mW cm−2), whereas the values measured in the asymmetric RF discharge were lower than 50 mW cm−2 for discharge powers in the range 10–100 W. The performances and limitations of both sensors are compared and discussed.

1 April 2015 in Vacuum
Verified
Journal Article
Closed access
JDJ. Dervaux
J. Dervaux
PCP.-A. Cormier
P.-A. Cormier
SKS. Konstantinidis
S. Konstantinidis
RCR. Di Ciuccio
R. Di Ciuccio
OCOlivier Coulembier
Olivier Coulembier
RSR. Snyders
R. Snyders