24 August 2017 in Wood Science and Technology
Three coupled two-dimensional viscoelastic creep models for orthotropic material are analyzed. The models of different complexity are mathematically formulated and implemented in a finite element software. Required viscoelastic material parameters are determined by calibration procedure, where numerical results are compared against experimentally obtained viscoelastic strains caused by tensile or shear loading. Finally, a comparison method is used to evaluate the accuracy of strain predictions of each particular model. The analysis shows that all the models are able to accurately predict viscoelastic creep simultaneously in two perpendicular directions for various periods of time and wood species. Calculated numerical values of the viscoelastic material parameters suitable for the three models and wood species, i.e., Douglas fir (Pseudotsuga menziesii), Norway spruce (Picea abies), Japanese cypress (Chamaecyparis obtusa), and European beech (Fagus sylvatica L.), under constant tensile loading are also given.
9 February 2018 in Wood Science and Technology
Rheological behavior of wood under uniaxial compression along and perpendicular to the grain in constant environment was examined. Tests with constant deformation rate until failure and stress relaxation tests with constant deformation applied stepwise were carried out. The experimental results of stress relaxation showed nonlinear material behavior over time that got more prominent under high deformation levels. Considerable amount of stress relaxed during applying the deformation. Wood experienced greater stress relaxation along the grain than perpendicular to it. Three rheological models for orthotropic material were calibrated to the experimentally determined stress–time curves in longitudinal and transverse directions simultaneously. Small deformation levels assuming linear strains were accounted for in the models. Required elastic material parameters were determined from the tests with constant deformation rate. A model including the highest number of viscoelastic material parameters was the most successful in predicting stress relaxation of wood under stepwise deformation. Modeling indicated that wood behavior was very close to linear viscoelastic in relaxation under small deformation. The obtained material parameters made the model suitable for predicting rheological behavior of wood comprehensively, under sustained deformation or load in constant conditions.
17 December 2020 in Holzforschung
The goal of the study was to analyze fracture properties of adhesive bond using a three-point end-notched flexure test and the compliance-based beam method. Critical strain energy release rates (G
IIc
) and cohesive laws were obtained for adhesive bonds made of European beech (Fagus sylvatica L.) and adhesives such as EPI, MUF, PRF and PUR. The experiments were assisted with FE analyses employing three different material models of wood: elastic (Elas), symmetric elasto-plastic (EP) and elasto-plastic with different compressive and tensile yield stresses parallel to fiber (EP+). The highest mean G
IIc
was achieved for PUR (5.40 Nmm−1) and then decreased as follows: 2.33, 1.80, 1.59 Nmm−1 for MUF, EPI, and PRF, respectively. The failure of bondline was brittle and occurred at bondline for EPI, MUF and PRF, and ductile and commonly occurring in wood for PUR adhesive. The FE simulations employing cohesive models agreed well with the experimental findings for all adhesives. FE model with Elas material was found accurate enough for EPI, MUF and PRF adhesives. For PUR adhesive, the model EP+ was found to be the most accurate in prediction of maximal force. The impact of friction between lamellas may be up to 4.2% when varying friction coefficient from 0 to 1. The impact of the grain angle distortion (α) with respect to longitudinal specimen axis showed its high influence on resulting stiffness and maximal force. It was found that three-point end-notched test is suitable for EPI, MUF, and PRF, while it is less appropriate for a bond with PUR adhesive due to notable plastic behavior.
8 November 2019 in Holzforschung
Changes in relative humidity of the ambient air, RH (%), cause wetting and drying of wood material, which results in non-uniform moisture contents or moisture gradients, and consequently in moisture-induced stresses and strains in the glued-laminated timber (glulam) members. The aim of the present paper is to perform a hygro-mechanical analysis to predict the mechanical behavior of glulam specimens exposed to two RH regimes, causing wetting from 50% to 90% RH and drying from 90% to 50% RH, and compare the numerical to the experimental results. The aims are also to quantitatively analyze the influence of characteristic material parameters required in the multi-Fickian moisture transport model and the mechanical model on moisture-induced strains and stresses in glulam specimens and to determine the possibility of cracking of the material by analyzing the maximum tensile stresses perpendicular to the grain. Accurate numerical predictions of moisture contents and moisture-induced strains are obtained in the glulam specimens during wetting and drying as compared to the experimental results. The influence of a particular characteristic material parameter on moisture-induced strains and stresses is characterized as significant, but not crucial when a rough numerical estimation of the mechanical behavior of the glulam beam exposed to RH changes is required.
1 April 2025 in Structures
9 August 2021 in Acta Mechanica