16 March 2015 in Geophysical Journal International
It is important to know the electrokinetic properties of crustal rocks for interpreting the conductivity mechanisms and seismoelectric phenomena during earthquakes and seismoelectric well logging. In this study, electrokinetic experiments are conducted using a special core-holder by employing an AC lock-in technique. A series of experiments are conducted on 10 sandstone samples to measure the streaming potentials and streaming currents, and the experiments on each sample are done at six different salinities. The streaming potential coefficient and streaming current coefficient are calculated from the measured streaming potentials and streaming currents. The experimental results show that streaming potential coefficient and streaming current coefficient decrease as the salinity increases. The dependence of these two coefficients on permeability and pore radius are analysed and compared with previous works. At low salinities, the streaming potential coefficient and streaming current coefficient increase with the increasing permeability and pore radius. At high salinities, the streaming potential coefficient (streaming current coefficient) almost share a same value for 10 different samples. This conclusion indicates that the differences of rock parameters can only be well recognized at lower salinities, and the electrokinetic signals are invalid at high salinities, which offers a restrictive condition for using the amplitude of electrokinetic signals to estimate rock parameters. The zeta-potential have also been estimated through combined measurements of streaming potential and streaming current. The surface conductivity and its contribution to electrokinetic effects are determined from a comparison of zeta-potentials by two different methods, and then the validation of the Helmholz–Smoluchowski equation for a capillary tube is tested in rocks. We also compare our date with theoretical and experimental works, and set up an expression about the relationship between zeta potential and salinity, which fits the experimental data well.
1 July 2021 in Journal of Petroleum Science and Engineering
15 April 2021 in Geophysical Journal International
SUMMARY: Thorough understanding of seismic signatures in cracked rocks is essential to estimate rock physical properties. Wave-induced fluid flow (or diffusion), scattering and Biot's global flow are three major mechanisms in controlling frequency-dependent attenuation and dispersion. To shed light on how those mechanisms and their interference affect the anisotropic features in cracked porous rocks, we develop an analytic model to estimate the angle-dependent attenuation and dispersion in such media. The most noteworthy feature of the model is that it is developed upon the exact solution of the problem of elastic wave scattered by a crack at oblique incidence. In particular, the poroelastic spring condition is applied to describe the influences of crack thickness and crack-filling fluid elasticity on wave scattering. Regardless of its complexity, we have showed that the model agrees with many benchmark theories under corresponding conditions, demonstrating its reasonability. It is found that the key factors that dominate anisotropic attenuation and dispersion are different in separating frequency regimes. At diffusion-dominated frequencies, the frequency-dependent anisotropic properties are mainly determined by the normal stress on the crack faces. In contrast, in Rayleigh scattering regime, they are greatly determined by the applied shear stress. At higher frequencies (Mie scattering regime), affected by the wave reflections between the crack edges, the frequency-dependent anisotropy becomes complex. The angle-dependent velocity can largely deviate from elliptic-shaped profile. As a result, the material properties cannot be described within the framework of the transversely isotropic medium model. Moreover, it is found that the attenuation is sensitive to the fluid compressibility and crack thickness, showing evidences that it is possible to invert fluid saturation and permeability from seismic attenuation. We also conclude that using a simple linear superposition of the attenuations due to wave-induced fluid flow and elastic scattering from their corresponding equivalent medium models will leads to an overestimation of the total attenuation. Our results demonstrate it is necessary to account for the mechanism interference to allow for an adequate estimation of the intrinsic attenuation of cracked porous rocks.
16 December 2020 in Geophysical Journal International
SUMMARY: When a seismic wave propagates in a fluid-saturated porous medium, a relative movement forms between the solid and the fluid and induces an electric current due to the electronic double layer. As a result, two kinds of seismoelectric coupling responses are generated in this procedure: the localized electric/magnetic field and interfacial electromagnetic wavefield. One important potential application of these two seismoelectric conversions is used for measuring formation P and S waves in well logging. Considering that the strong collar wave seriously affects the velocity measurements of formation P and S waves in current acoustic logging while drilling (LWD), the seismoelectric LWD method, which combines seismoelectric conversion and acoustic LWD technique, was suggested to be a novel method in oil and gas exploration. The collar wave cannot induce any seismoelectric signal on the metal collar since there is no double layer formed on a metal surface. In this paper, acoustic and seismoelectric LWD measurements are conducted in the laboratory. We build a scaled multipole acoustic LWD tool to conduct acoustic measurements in a water tank and a sandstone borehole model. We also build a multipole seismoelectric LWD tool and record the seismoelectric signals induced with the same acoustic source. Then, we compare the recorded acoustic and seismoelectric signals by using the experimental data. The result indicates that the apparent velocities of seismoelectric signals are equal to the formation P- and S-wave velocities and the collar waves do not induce any visible electric signal in the full waveforms. We further analyse the mechanism of seismoelectric LWD by a quantitative comparison of the amplitudes between the inner collar wave and outer collar wave. The results show that the amplitude of outer collar wave decreases significantly when it radiates out of the tool, so that the seismoelectric signals induced by collar waves are too weak to be distinguished in the full waveforms of seismoelectric LWD measurements. Thus, the formation P- and S-wave velocities are detected accurately from the recorded seismoelectric LWD data. These results verify the feasibility of the seismoelectric LWD method for measuring acoustic velocities of the borehole formation.
19 October 2015 in Geophysical Journal International
Seismoelectric logging has potential applications in exploring the porous formation characteristics. In this study, we theoretically address how the amplitudes of the Stoneley wave and its accompanying borehole seismoelectric field depend on the porous formation parameters such as porosity, permeability and tortuosity. We calculate the ratio of the electric field amplitude to the pressure amplitude (REP amplitude) for the low-frequency Stoneley wave of different formations and find that the REP amplitude is sensitive to porosity and tortuosity but insensitive to permeability. To confirm this conclusion, we derive the approximate expression of the REP amplitude in the wavenumber–frequency domain which shows that the REP amplitude is dependent on tortuosity but independent of permeability. This contradicts the result concluded by previous researchers from experiments that the REP amplitude is directly proportional to the permeability. The reason is probably attributed to the fact that the rock samples with different permeabilities typically have different tortuosities. Since the REP amplitude is sensitive to tortuosity, we propose a method of estimating formation tortuosity from seismoelectric logs. It is implemented by using the REP amplitude and the wavenumber of the Stoneley wave at a given frequency when the porosity and the pore fluid viscosity and salinity are known. We test the method by estimating the tortuosities from the synthetic seismoelectric waveforms in different formations. The result shows that the errors relative to the input tortuosities are lower than 5.0 per cent without considering the uncertainties of other input parameters.
1 July 2019 in Computers & Geosciences