Yunpeng Liu

Yunpeng Liu

Auto-generated profile, based on publicly available information

Yunpeng Liu

Wuhan University of Technology

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2023 in Journal of Cleaner Production
Verified
Journal Article
Closed access
YLYunpeng Liu
Yunpeng Liu
WWWenhao Wan
Wenhao Wan
Jian-Xin LuJian-Xin Lu
Jian-Xin Lu
CPChi Sun Poon
Chi Sun Poon
SHShuguang Hu
Shuguang Hu
FWFazhou Wang
Fazhou Wang

4 April 2019 in Journal of the American Ceramic Society
Verified
Journal Article
Closed access
PDF file
CLChen Liu
Chen Liu
YLYunpeng Liu
Yunpeng Liu
ZLZhichao Liu
Zhichao Liu
CHChuanlin Hu
Chuanlin Hu
XHXiao Huang
Xiao Huang
FWFazhou Wang
Fazhou Wang

23 September 2025 in Construction and Building Materials
Verified
Journal Article
Closed access
JWJiantao Wang
Jiantao Wang
YLYunpeng Liu
Yunpeng Liu
ZLZhichao Liu
Zhichao Liu
SHShuguang Hu
Shuguang Hu
FWFazhou Wang
Fazhou Wang

1 April 2025 in Advances in Cement Research
Verified
Journal Article
Closed access
YLYunpeng Liu
Yunpeng Liu
YCYingying Cui
Yingying Cui
XTXianxin Tong
Xianxin Tong
In this study, cement was regenerated using completely recyclable mortar (CRM) as raw cement meals. The effects of silica modulus (SM) and alumina modulus (AM) on the properties of CRM, burnability of raw meal and the clinker’s properties were studied. The results showed that, with a higher SM and lower AM, less melt would be available to facilitate the diffusion of calcium oxide towards belite to form alite. The compressive strength of recycled cement increased with the increase of AM when SM = 2.7 and 2.2 and decreased with the increase of AM at a low SM (SM = 1.7). The suggested rate value of raw meals using CRM is a medium SM (SM = 2.2 or SM = 2.7) and AM = 1.5–1.8 with a calcination temperature of 1400°C. The strength of both the CRM and the recycled cement clinker obtained is relatively high. Moreover, the calcination temperature could be further reduced to 1300°C or 1350°C with a low SM (SM = 1.7) and AM (AM = 0.9–1.5). Although the CRM had a lower early strength, it had a relatively high strength in the later stage. However, its water absorption was significantly increased compared to the control group.

10 June 2026 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
CLChenxi Liu
Chenxi Liu
ZPZhifeng Pan
Zhifeng Pan
ZLZongze Lu
Zongze Lu
YLYunpeng Liu
Yunpeng Liu
Critical chloride concentration ( C th ) for depassivation is an essential parameter for ensuring the durability of reinforced concrete structures, while the mechanism by which chlorides initiate the failure of the passive film at this threshold remains debated. C th required by passive film breakdown was determined by a cyclic potentiodynamic polarization test here. A combination of Mott-Schottky test and X-ray photoelectron spectroscopy was further applied to explore the semiconductive properties and chemical composition of the film under this critical environment. The results show that this C th is lower than that determined by a sharp change in corrosion potential, polarization resistance, or corrosion current density. Neither the pitting potential nor the cation vacancy concentration is sensitive to chloride near this threshold. The role of chloride is to accelerate the passive film dissolution, causing the film to thin and eventually break down. It does not penetrate the film or even reach the metal substrate.

10 July 2023 in Journal of Testing and Evaluation
Verified
Journal Article
Closed access
PDF file
SYShuang Yang
Shuang Yang
JWJiantao Wang
Jiantao Wang
WLWen LI
Wen LI
YWYingxiang Wang
Yingxiang Wang
YLYunpeng Liu
Yunpeng Liu
Coarse aggregates were pretreated with asphalt emulsion to concentrate asphalt film in the interfacial transition zone (ITZ) so as to improve concrete impermeability at a relatively low polymer content. Several test methods, including artificial crack samples, model aggregate concrete, and surface element scanning, were employed to characterize the contribution of modified ITZ to concrete impermeability. The results showed that incorporating hydrophobic asphalt film in ITZ could simultaneously slow down water absorption while weakening the ITZ microstructure. The water absorption of concretes decreased with an increase in the asphalt content and asphalt-coated aggregates ratio. However, the rapid chloride migration tests showed different results, which could be attributed to the different water saturation states of concretes before the tests. The hydrophobic asphalt film could retard water absorption and, consequently, chloride ion diffusion, even in the presence of cracks.