Dana Hollins

Dana Hollins

Auto-generated profile, based on publicly available information

Dana Hollins

Cardno ChemRisk, San Francisco, CA, USA

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 August 2017 in Inhalation Toxicology
Verified
Journal Article
Closed access
JPJennifer S. Pierce
Jennifer S. Pierce
ARAlexander S. Riordan
Alexander S. Riordan
EMEric W. Miller
Eric W. Miller
SGShannon H. Gaffney
Shannon H. Gaffney
DHDana M. Hollins
Dana M. Hollins
Talc has been used for over a century in a variety of cosmetic products. While pure cosmetic talc (free of asbestos) is not considered a risk factor for mesothelioma, it has been recently suggested that inhalation of cosmetic talc containing trace levels of asbestos is a risk factor for mesothelioma. Bulk analyses of cosmetic talcum products were performed in the 1960s and 1970s, however, the analytical methods used at that time were incapable of determining whether asbestos minerals were present in the asbestiform versus non-asbestiform habit. The distinction between these two mineral habits is critical, as non-asbestiform amphibole minerals do not present an asbestos-related cancer risk via inhalation. As such, we evaluated six historical talcum powders using modern-era analytical methods to determine if asbestos is present, and if so, to identify the mineral habit (asbestiform versus non-asbestiform) of the asbestos. Based on their labels, the products were produced by four manufacturers and sold between 1940 and 1977. The products were analyzed in duplicate by two laboratories using standard protocols. Laboratory A analyzed samples using X-ray diffraction (XRD) and polarized light microscopy (PLM), and Laboratory B analyzed samples using PLM and transmission electron microscopy (TEM) with energy dispersive X-ray analysis (EDX) and selected area electron diffraction (SAED). No asbestiform minerals were found in any of the products. Nonetheless, even if some historical cosmetic talcum products contained trace amounts (≤0.1%) of asbestiform minerals, any resulting asbestos exposure would be expected to be exceedingly low, and comparable to exposures from breathing ambient air.

1 September 2020 in Toxicology and Industrial Health
Verified
Journal Article
Closed access
PDF file
NJNeva Jacobs
Neva Jacobs
KCKathy Chan
Kathy Chan
VLVeruscka Leso
Veruscka Leso
ADAndrea D’aNna
Andrea D’aNna
DHDana Hollins
Dana Hollins
Ivo IavicoliIvo Iavicoli
Ivo Iavicoli
Various decontamination methods that may be used to extend respirator inventories have been examined for over a decade. In light of the ongoing coronavirus disease 2019 pandemic, many health-care settings are now implementing these techniques amid respirator shortages. We sought to perform a critical review of the available literature regarding decontamination methods to determine which strategies are effective at inactivating the target organism, preserve performance (filter efficiency and fit) of the respirator, leave no residual toxicity from the treatment, and are fast-acting, inexpensive, and readily available. We also identified areas for future research. We found that ultraviolet germicidal irradiation (UVGI) is the most widely studied method, and treatments are effective at inactivating SARS-CoV-2 without diminishing filtration efficiency or fit. These treatments were found to leave no residual toxicity for the wearer, have a relatively short cycle time of less than 1 h, and existing systems can likely be retrofitted to accommodate this method. Further, UVGI (among other treatment methods) has been recommended by the Centers for Disease Control and Prevention (CDC), Occupational Safety and Health Administration (OSHA), and respirator manufacturers. Methods involving microwave-generated steam also show potential in that they are likely effective against SARS-CoV-2, preserve performance, have no residual toxicity, require a short duration treatment cycle (often less than 10 min), and microwave ovens are inexpensive and readily available. Steam methods are currently recommended by the CDC, OSHA, and manufacturers. These respirator decontamination methods are likely also useful against other viruses or pathogens.

1 September 2020 in Toxicology and Industrial Health
Verified
Journal Article
Open access
PDF file
DHDana Hollins
Dana Hollins
AKAnthony L Kiorpes
Anthony L Kiorpes

1 November 2019 in Toxicology and Industrial Health
Verified
Journal Article
Closed access
PDF file
DHDana Hollins
Dana Hollins
ABAmanda Burns
Amanda Burns
KUKen Unice
Ken Unice
DPDennis J Paustenbach
Dennis J Paustenbach
The objective is to present historical asbestos airborne concentrations associated with activities involving presumably asbestos-containing materials in steel mills. A total of 138 historical industrial hygiene air samples collected in three US steel mills from 1972 to 1982 were analyzed. The majority of samples were collected during relining of open hearth furnaces, stoves, and blast furnaces by steel mill bricklayers and bricklayer helpers. Over 75% of the samples (n = 106) were collected for 50 min or less, four samples were collected for 227 to 306 min, and sample durations were not reported for the remaining 28 samples. Average airborne fiber concentrations measured during relining activities of open hearth furnaces, stoves, and blast furnaces were 0.21 f/cc, 0.72 f/cc and 0.13 f/cc phase-contrast microscopy (PCM), respectively. Measured airborne fiber concentrations of four time-weighted average (TWA) samples (>227 min) averaged 0.045 f/cc. Estimated 8-h TWAs concentrations averaged 0.34 f/cc for bricklayers and 0.2 f/cc bricklayer helpers. While 8-h TWA concentration estimates for monitored tasks/jobs may often have exceeded current Occupational Safety and Health Administration (OSHA) Permissible Exposure Limits (PELs), they did not exceed relevant contemporaneous occupational exposure standards. This analysis provides a better understanding of historical airborne asbestos exposures that bricklayers and other tradesmen experienced during furnace and stove work in the US steel mills.