3 January 2016 in Annual Review of Fluid Mechanics
A drop hitting a solid surface can deposit, bounce, or splash. Splashing arises from the breakup of a fine liquid sheet that is ejected radially along the substrate. Bouncing and deposition depend crucially on the wetting properties of the substrate. In this review, we focus on recent experimental and theoretical studies, which aim at unraveling the underlying physics, characterized by the delicate interplay of not only liquid inertia, viscosity, and surface tension, but also the surrounding gas. The gas cushions the initial contact; it is entrapped in a central microbubble on the substrate; and it promotes the so-called corona splash, by lifting the lamella away from the solid. Particular attention is paid to the influence of surface roughness, natural or engineered to enhance repellency, relevant in many applications.
12 July 2019 in Journal of Fluid Mechanics
This paper is dedicated to the solidification of a water drop impacting a cold solid surface. In the first part, we establish a one-dimensional (1-D) solidification model, derived from the Stefan problem, that aims at predicting the freezing dynamics of a liquid on a cold substrate, taking into account the thermal properties of this substrate. This model is then experimentally validated through a 1-D solidification set-up, using different liquids and substrates. In the second part, we show that during the actual drop spreading, a thin layer of ice develops between the water and the substrate and pins the contact line at its edge when the drop reaches its maximal diameter. The liquid film then remains still on the ice and keeps freezing. This configuration lasts until the contact line eventually unpins and the liquid film retracts on the ice. We measure and interpret this crucial time of freezing during which the main ice layer is built. Finally, we compare our 1-D model prediction to the thickness of this ice pancake and we find a very good agreement. This allows us to provide a general expression for the frozen drop’s main thickness, using the drop’s impact and liquid parameters.
10 August 2016 in Journal of Fluid Mechanics
We investigate the dynamics of drop impact on a thin liquid film at short times in order to identify the mechanisms of splash formation. Using numerical simulations and scaling analysis, we show that it depends both on the inertial dynamics of the liquid and the cushioning of the gas. Two asymptotic regimes are identified, characterized by a new dimensionless number $J$ : when the gas cushioning is weak, the jet is formed after a sequence of bubbles are entrapped and the jet speed is mostly selected by the Reynolds number of the impact. On the other hand, when the air cushioning is important, the lubrication of the gas beneath the drop and the liquid film controls the dynamics, leading to a single bubble entrapment and a weaker jet velocity.
29 November 2017 in Journal of Fluid Mechanics
We investigate droplet impact on a solid substrate in order to understand the influence of the gas in the splashing dynamics. We use numerical simulations where both the liquid and the gas phases are considered incompressible in order to focus on the gas inertial and viscous contributions. We first confirm that the dominant gas effect on the dynamics is due to its viscosity through the cushioning of the gas layer beneath the droplet. We then describe an additional inertial effect that is directly related to the gas density. The two different splashing mechanisms initially suggested theoretically are observed numerically, depending on whether a jet is created before or after the impacting droplet wets the substrate. Finally, we provide a phase diagram of the drop impact outputs as the gas viscosity and density vary, emphasizing the dominant effect of the gas viscosity with a small correction due to the gas density. Our results also suggest that gas inertia influences the splashing formation through a Kelvin–Helmholtz-like instability of the surface of the impacting droplet, in agreement with former theoretical works.
22 June 2022 in Physical Review Letters
The effect of freezing on contact line motion is a scientific challenge in the understanding of the solidification of capillary flows. In this Letter, we experimentally investigate the spreading and freezing of a water droplet on a cold substrate. We demonstrate that solidification stops the spreading because the ice crystals catch up with the advancing contact line. Indeed, we observe the formation and growth of ice crystals along the substrate during the drop spreading, and show that their velocity equals the contact line velocity when the drop stops. Modeling the growth of the crystals, we predict the shape of the crystal front and show that the substrate thermal properties play a major role on the frozen drop radius.
1 May 2017 in Physica D: Nonlinear Phenomena