1 November 2019 in Journal of Vacuum Science & Technology A
Chemical reaction probabilities, defined as the number of silicon atoms removed per incident fluorine atom, have been investigated in mixtures of NF3 and SF6 plasmas in an inductively-coupled plasma reactor. Fluorine atom densities were measured by optical emission actinometry, and isotropic etching rates were measured by the degree of undercutting of SiO2-masked silicon by cross-sectional scanning electron microscopy. In addition, atomic force microscopy was used to examine surface morphology of etched Si surfaces. The F atom reaction probabilities derived from isotropic etching rates indicate an ∼30-fold higher reaction probability in SF6 plasmas compared with values in NF3 plasmas. Surfaces etched in SF6 plasmas were much smoother than those etched in NF3 plasmas. The addition of only 10% SF6 to an NF3 plasma produced a much higher reaction probability (∼5-fold) than in a pure NF3 plasma. This surprising enhancement of reaction probabilities for F with Si in SF6 plasmas is further investigated, based on the mechanism of adsorbed sulfur acting as a catalyst to greatly enhance the etching rate of Si. Dilute sulfur solutions in isopropyl alcohol were allowed to evaporate on the masked Si samples, depositing sulfur in relatively high concentrations near mask edges in ∼2 μm diameter periodic “strings of beads.” The sulfur-dosed sample etched several times faster at the center of each bead than a sample not exposed to sulfur that was placed side by side. The catalytic effect of sulfur is ascribed to an enhanced F sticking coefficient and/or decreased desorption rate on a surface covered with sulfur.
11 January 2019 in Journal of Applied Physics
Studies of power-modulated chlorine inductively coupled plasmas (ICPs) bounded by yttria-coated chamber walls are presented. Time-resolved optical emissions from Cl and Xe actinometry trace gas were recorded over the 740–920 nm region as power at 13.56 MHz was modulated between high power and no power. The intensity ratio of Cl-to-Xe emission, proportional to Cl number density, nCl, followed the modulation in power, allowing Cl heterogeneous loss coefficients, γCl, to be obtained from a simple time-resolved, 0-dimensional model of the afterglow period that best matched computed relative changes in nCl at the beginning and end of the powered period, with γCl as the only adjustable parameter. This approach only requires a treatment of diffusion and avoids complications introduced by attempting simulations of the full modulation period. Cl recombination coefficients were determined on the mostly yttria surfaces for Cl2 ICPs (a) immediately after NF3 plasma cleaning (γCl = 0.20), (b) during long exposure to the Cl2 plasma with no substrate bias (γCl = 0.11), and (c) during Si etching with substrate bias (γCl = 0.055-0.070). For Cl2/5% O2 ICPs, these values are 0.28, 0.17, and 0.030, respectively. These results compare favorably to qualitative behavior reported previously for continuous Cl2 and Cl2/O2 ICPs in this yttria-coated chamber.
1 August 2012 in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
1 February 2019 in Plasma Sources Science and Technology
Time-dependent studies of power-modulated chlorine inductively-coupled plasmas are presented. Power at 13.56 MHz applied to the plasma was modulated between high and low power states. Time-resolved optical emission, power delivery, and Langmuir probe measurements revealed at least two conditions upon switching from high to low power: a ‘normal’ mode in which electron temperature ( T
e
) remains constant, while electron and ion number densities ( n
e
and n + ) and optical emission spectroscopic (OES) intensities smoothly drop to a level roughly equal to the fractional drop in power, and an ‘abnormal’ mode in which n
e
, n + and OES intensities plummet before the plasma re-ignites and these values rise to levels more commensurate with the drop in power. Whether the plasma operates in the normal or abnormal mode is sensitive to impedance matching conditions and is also a function of pressure and pulsing parameters. This ignition delays in the abnormal mode can be qualitatively understood in terms of a power balance model commonly used to explain instability-induced, self-modulation in highly electronegative plasmas, caused by the slower time response of negative ions compared with electrons. The study indicates that power modulation for added control in processes such as plasma etching will require careful measurement and possibly control of power with microsecond resolution.
12 August 2009 in Journal of Polymer Research
14 December 2017 in Langmuir