1 September 2013 in Journal of Vacuum Science & Technology A
The field of plasma etching is reviewed. Plasma etching, a revolutionary extension of the technique of physical sputtering, was introduced to integrated circuit manufacturing as early as the mid 1960s and more widely in the early 1970s, in an effort to reduce liquid waste disposal in manufacturing and achieve selectivities that were difficult to obtain with wet chemistry. Quickly,the ability to anisotropically etch silicon, aluminum, and silicon dioxide in plasmas became the breakthrough that allowed the features in integrated circuits to continue to shrink over the next 40 years. Some of this early history is reviewed, and a discussion of the evolution in plasma reactor design is included. Some basic principles related to plasma etching such as evaporation rates and Langmuir–Hinshelwood adsorption are introduced. Etching mechanisms of selected materials, silicon,silicon dioxide, and low dielectric-constant materials are discussed in detail. A detailed treatment is presented of applications in current silicon integrated circuit fabrication. Finally, some predictions are offered for future needs and advances in plasma etching for silicon and nonsilicon-based devices.
7 June 2024 in Journal of Vacuum Science & Technology B
Plasma etching is an essential semiconductor manufacturing technology required to enable the current microelectronics industry. Along with lithographic patterning, thin-film formation methods, and others, plasma etching has dynamically evolved to meet the exponentially growing demands of the microelectronics industry that enables modern society. At this time, plasma etching faces a period of unprecedented changes owing to numerous factors, including aggressive transition to three-dimensional (3D) device architectures, process precision approaching atomic-scale critical dimensions, introduction of new materials, fundamental silicon device limits, and parallel evolution of post-CMOS approaches. The vast growth of the microelectronics industry has emphasized its role in addressing major societal challenges, including questions on the sustainability of the associated energy use, semiconductor manufacturing related emissions of greenhouse gases, and others. The goal of this article is to help both define the challenges for plasma etching and point out effective plasma etching technology options that may play essential roles in defining microelectronics manufacturing in the future. The challenges are accompanied by significant new opportunities, including integrating experiments with various computational approaches such as machine learning/artificial intelligence and progress in computational approaches, including the realization of digital twins of physical etch chambers through hybrid/coupled models. These prospects can enable innovative solutions to problems that were not available during the past 50 years of plasma etch development in the microelectronics industry. To elaborate on these perspectives, the present article brings together the views of various experts on the different topics that will shape plasma etching for microelectronics manufacturing of the future.
6 February 2012 in Journal of Vacuum Science & Technology A
The authors report a new, important phenomenon: photo-assisted etching of p-type Si in chlorine-containing plasmas. This mechanism was discovered in mostly Ar plasmas with a few percent added Cl2, but was found to be even more important in pure Cl2 plasmas. Nearly monoenergetic ion energy distributions (IEDs) were obtained by applying a synchronous dc bias on a “boundary electrode” during the afterglow of a pulsed, inductively coupled, Faraday-shielded plasma. Such precisely controlled IEDs allowed the study of silicon etching as a function of ion energy, at near-threshold energies. Etching rates increased with the square root of the ion energy above the observed threshold of 16 eV, in agreement with published data. Surprisingly, a substantial etching rate was observed, independent of ion energy, when the ion energy was below the ion-assisted etching threshold. Experiments ruled out chemical etching by Cl atoms, etching assisted by Ar metastables, and etching mediated by holes and/or low energy electrons generated by Auger neutralization of low-energy ions, leaving photo-assisted etching as the only likely explanation. Experiments were carried out with light and ions from the plasma either reaching the surface or being blocked, showing conclusively that the “sub-threshold” etching was due to photons, predominately at wavelengths < 1700 Å. The photo-assisted etching rate was equal to the ion-assisted etching rate at 36 eV, causing substantial complications for processes that require low ion energies to achieve high selectivity and low damage, such as atomic layer etching. Under these conditions, photo-assisted etching likely plays an important role in profile evolution of features etched in Si with chlorine-containing plasmas, contributing to the commonly observed sloped sidewalls and microtrenches.
16 May 2017 in Journal of Physics D: Applied Physics
Atomic layer etching (ALE) of SiO 2 was studied by alternating exposure of a 5 nm-thick SiO 2 film on Si substrate to (1) a plasma beam emanating from a c-C 4 F 8 inductively coupled plasma (ICP), to grow a fluorocarbon (FC) film composed mainly of CF 2 , and (2) an energetic (130 eV) Ar + ion beam extracted from a separate Ar ICP. In situ x-ray photoelectron spectroscopy was used to analyze the chemical composition of the near-surface region, and to quantify the thickness of the FC and SiO 2 films. A very thin (3–6 Å), near self-limiting thickness CF 2 -rich FC film was found to deposit on the SiO 2 surface with exposure to continuous or pulsed power C 4 F 8 plasma beams, under conditions that generated a large relative flux of CF 2 . Following this, a FC film of similar composition grew at ~10 times slower rate. Exposure of the thin film to the Ar + beam led to removal of 1.9 Å SiO 2 . An estimated yield of 1.3 SiO 2 molecules-per-Ar + was found for a single ALE step. The rate of 1.9 Å/cycle persisted over multiple ALE cycles, but a carbon-rich residual film did build up. This film can be removed by a brief exposure to an O 2 -containing plasma beam.
29 December 2008 in Applied Physics Letters
The energy distribution of ballistic electrons in a dc/rf hybrid parallel-plate capacitively coupled plasma reactor was measured. Ballistic electrons originated as secondaries produced by ion and electron bombardment of the electrodes. The energy distribution of ballistic electrons peaked at the value of the negative bias applied to the dc electrode. As that bias became more negative, the ballistic electron current on the rf substrate electrode increased dramatically. The ion current on the dc electrode also increased.
3 June 2024 in Journal of Vacuum Science & Technology B
Low-temperature plasmas (LTPs) are essential to manufacturing devices in the semiconductor industry, from creating extreme ultraviolet photons used in the most advanced lithography to thin film etching, deposition, and surface modifications. It is estimated that 40%–45% of all process steps needed to manufacture semiconductor devices use LTPs in one form or another. LTPs have been an enabling technology in the multidecade progression of the shrinking of device dimensions, often referred to as Moore’s law. New challenges in circuit and device design, novel materials, and increasing demands to achieve environmentally benign processing technologies require advances in plasma technology beyond the current state-of-the-art. The Department of Energy Office of Science Fusion Energy Sciences held a workshop titled Plasma Science for Microelectronics Nanofabrication in August 2022 to discuss the plasma science challenges and technical barriers that need to be overcome to continue to develop the innovative plasma technologies required to support and advance the semiconductor industry. One of the key outcomes of the workshop was identifying a set of priority research opportunities (PROs) to focus attention on the most strategic plasma science challenges to address to benefit the semiconductor industry. For each PRO, scientific challenges and recommended strategies to address those challenges were identified. This article summarizes the PROs identified by the workshop participants.